ZL0012-0C PAGE 1 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 05123Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.TMRELAYSINSTALLATION GUIDE10A SPDT Mini Command RelayInstaller’s SpecificationsOperating Temperature -0°C to 60°C (-32° to 140°F)Operating Humidity 10-90% non condensingExpected Relay Life Electrical (at rated current): 100,000 cycles Mechanical (unpowered): 10,000,000 cyclesRelay Status LED ON=energizedInsulation Class 277 VAC RMSWire Specifications: Lead Length 10” (254mm) min. Gauge UL1015; Coil: 18AWG; Contacts: 16AWGAgency Approvals UL508 enclosed device listing, pollution degree 2V645V645DIMENSIONSNOTICE• This product is not intended for life or safety applications.• Do not install this product in hazardous or classified locations.• The installer is responsible for conformance to all applicable codes.• Mount this product inside a suitable fire and electrical enclosure.INSTALLATIONDisconnect and lock out all power sources before beginning the installation.1. Mount the unit using the DIN rail clip or the screw.2. Connect coil:• Choose the coil common lead (white with yellow stripe) and connect it to the common (-) source termination point.• Choose either the low voltage (24-30 VAC/DC, white with blue stripe) or high voltage (120 VAC, white with black stripe) lead, depending on the application requirements, and connect it to the (+) source termination point.*3. Connect relay contacts:• Choose the relay common wire (yellow) and connect to the switched load.• Choose the relay N.O. (orange) or N.C. (blue) lead* and connect to the switched load.4. Secure the enclosure and reconnect power.* Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e. wire nut.1.1”(28 mm)1.3”(33 mm)0.6(14 mm)1.2(30 mm)1.1(28 mm)0.5(13 mm)Ø 0.15”(4 mm)HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.• This equipment must only be installed and serviced by qualified electrical personnel.• Read, understand and follow the instructions before installing this product.• Turn off all power supplying equipment before working on or inside the equipment.• Use a properly rated voltage sensing device to confirm power is off. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATIONFailure to follow these instructions will result in death or serious injury.DANGER ZL0012-0C PAGE 2 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 05123Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.TMV645INSTALLATION GUIDEN.C.Common24VAC/DC120VACHIwht/blackLOWwht/blueCOMMwht/yellowCommonN.O.CONTACT OUTPUTCONTROL SYSTEM INPUTWhiteYELLOWWhiteWhiteORANGEblack black blue blue yellow yellow black WIRING EXAMPLEWIRING COLOR CODESCONTACT AND COIL SPECIFICATIONSVoltage Coil Current AC DC 24-30V................................. 32mA 13mA120V...................................... 17mA — TYPICAL COIL PERFORMANCEResistive................. 10A@250VAC, N.O. 7A@250VAC, N.C. 6A@277VAC 7A@30VDCMotor..................... 125VAC, 1/4 HP, N.0.CONTACT RATINGSV645To Load24V120VDIGITALCONTROLPANELCoilV645To Load24V120VPOWERSOURCEPANELCoilNext >