Z202851-0D PAGE 1 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 03121 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. TM RELAYS INSTALLATION GUIDE 10 A SPDT Enclosed Relay 10-30 VDC/AC or 120 VAC Coil Installer’s Specifications Operating Temperature -34°C to 60°C (-29° to 140°F) Operating Humidity 10-90% non condensing Expected Relay Life Electrical (at rated current): 100,000 cycles Mechanical (unpowered): 10,000,000 cycles Relay Status LED ON=energized Wire Specifications: Lead Length 14” (356mm) min. Gauge UL1015; Coil: 18 AWG; Contacts: 16 AWG Insulation Class 600 VAC RMS Agency Approvals UL508 enclosed device listing V100 V100 DIMENSIONS NOTICE • This product is not intended for life or safety applications. • Do not install this product in hazardous or classified locations. • The installer is responsible for conformance to all applicable codes. • Mount this product inside a suitable fire and electrical enclosure. INSTALLATION Disconnect and lock out all power sources before beginning the installation. 1. Using the threaded nipple, connect the relay to the desired enclosure through a knock out hole. 2. Secure with the conduit nut provided. 3. Connect Coil: • Choose the coil common lead (white with yellow stripe) and connect it to the (-) source termination point. • Choose either the low voltage (10-30 VAC/DC, white with blue stripe) or high voltage (120 VAC, white with black stripe) lead, depending on the application requirements, and connect it to the (+) source termination point.* 4. Connect Relay Contacts: • Choose the relay common wire (yellow) and connect to switched load. • Choose the relay N.O. (orange) and/or* N.C. (blue) lead and connect to switched load. 5. Secure the enclosure and reconnect power. * Isolate or insulate all non-terminated wires according to local electrical code requirements, i.e. wire nut. 1.6" (41 mm) 1.7" (43 mm) 1/2" NPT Nipple 1.8" (46 mm) 2.9" (74 mm) 2.8" (71 mm) HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes. • This equipment must only be installed and serviced by qualified electrical personnel. • Read, understand and follow the instructions before installing this product. • Turn off all power supplying equipment before working on or inside the equipment. • Use a properly rated voltage sensing device to confirm power is off. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION Failure to follow these instructions will result in death or serious injury. DANGER RoHS CompliantZ202851-0D PAGE 2 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 03121 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. TM V100 INSTALLATION GUIDE N.C. Common 10-30VAC/DC 120VAC HI wht/black LOW wht/blue COMM wht/yellow Common N.O. CONTACT OUTPUTCONTROL SYSTEM INPUT White YELLOW White White ORANGE b l a c k b l a c k b l u e b l u e y e l l o w y e l l o w b l a c k WIRING EXAMPLE Nipple mount directly to a panel Nipple mount to any 2x or 4x electrical box To Load To Controls COIL CONTACTS To Load To Controls Wire Nut C O I L CONTACTS WIRING COLOR CODES CONTACT AND COIL SPECIFICATIONS Pull in Voltage AC DC 10-30V..................................... 8 9 120V........................................ 78 Drop Out Voltage AC DC 10-30V..................................... 2 3 120V........................................ 18 Voltage Coil Current AC DC 10V.......................................... 25mA 14mA 12V.......................................... 25mA 14mA 24V.......................................... 31mA 16mA 30V.......................................... 39mA 18mA 120V........................................ 22mA - TYPICAL COIL PERFORMANCE CONTACT RATINGS Resistive .............. 10A@277VAC, 28VDC Motor .................... 120VAC, 1/3HP N.O. & 1/6HP N.C. 240VAC, 1/3HP N.O. & 1/6HP N.C. 277VAC, 1/4HP N.O. & 1/8HP N.C. Pilot Duty ............. 277VAC, (1.7A), 480VA N.O. Ballast .................. 277VAC, 1.7A Tungsten ............... 120VAC, TV3 N.O. TV2 N.C. Gold Flash ............. YesNext >