Z203571-0K Page 1 of 2 ©2019 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 0119 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. Other companies’ trademarks are hereby acknowledged to belong to their respective owners. NOTICE • This product is not intended for life or safety applications. • Do not install this product in hazardous or classied locations. • Read and understand the instructions before installing this product. • Turn o all power supplying equipment before working on it. • The installer is responsible for conformance to all applicable codes. If this product is used in a manner not specied by the manufacturer, the protection provided by the product may be impaired. No responsibility is assumed by the manufacturer for any consequences arising out of the use of this material. Installation Guide Temperature Product Identification Product Overview The TJ Series temperature sensor is designed for VAV systems. The cable is plenum rated, and the probe is stainless steel for durability. The TJ is warranted for a period of five years. TJ Series VAV Discharge Temperature Sensor Specifications Wiring 22 AWG; 2-wire RTD/Thermistor Probe Stainless steel Operating Temperature Probe: -25° to 105 °C (-13 to 221 °F) Wiring side: Up to 75 °C (167 °F) WARRANTY Limited Warranty 5 years Sensor TypeOptionProbe Length B = 4" (102 mm) D = 8" (204 mm) TJ 0 = Standard 5 ft. cable, no QDs 1 = 1/4" Female Quick Discon- nects (QD) 2 = 1/4” QDs with 8 ft. lead wires 3 = 10 ft. cable, no QDs = Resistive Cal Certificate 0 = None 2 = 3-Point NIST calibration R Output B = 100R platinum, RTD C = 1k platinum, RTD D = 10k T2, Thermistor E = 2.2k, Thermistor F = 3k, Thermistor H = 10k T3, Thermistor I = 1k Balco (Nickel-Iron) RTD J = 10k Dale, Thermistor K = 10k w/11k shunt, Thermistor M = 20k NTC, Thermistor N = 1800 ohm, Thermistor T = 100k, Thermistor W = 10k T2 high accuracy, Thermistor Y = 10k T3 high accuracy, Thermistor Notes: Increased cable length affects the readings of lower resistance RTDs (100R platinum RTD). Room temperature offset documented on each unit. TJZ203571-0K Page 2 of 2 ©2019 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 0119 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. Other companies’ trademarks are hereby acknowledged to belong to their respective owners. TJ Series Installation Guide TM Dimensions L 0.3" (6.3 mm) Optional 1/4” female quick disconnect 1.5" (38 mm) 2" (51 mm) 1.1" (28 mm) 1" (26 mm) Installation 1. Remove adhesive covering from foam gasket. 2. Push probe through hole in gasket until gasket adheres to underside of mounting flange. 3. Drill a 3/8” diameter hole in the duct for the sensor probe. 4. Mount flange to duct using screws provided. 5. Wire as shown. Thermistor RTDNext >