Wiring22 AWG; 2-wire: RTD/Thermistor ProbeStainless steel Operating Temp-25 to 105 °C (-13 to 221 °F) LINITEMP OPTION Input PowerClass 2; 5 to 30 Vdc Output10mV/°C Operating Temp-25 to 105 °C (-13 to 221 °F) Calibration Offset 1.5 °C (2.7 °F) typical; 2.5 °C (4.5 °F) max. at 25 °C (77 °F)* Offset over Temp 1.8 °C (3.24 °F) typical; 3.0 °C (5.4 °F) max. over 0 to 70 °C (32 to 158 °F) range; 2.0 °C (3.6 °F) typical, 3.5 °C (6.3 °F) max. over -25 to 105 °C (-13 to 221 °F) range WARRANTY Limited Warranty 5 years TJ The TJ Series temperature sensors are highly accurate and cost effective, with trouble-free installation. The sensor is encased in a sturdy corrosion-resistant stainless steel probe. A variety of RTD/thermistor sensor and probe length options are available for maximum versatility in applications. Increased cable length affects the readings of lower resistance RTDs (100R platinum, RTD). * Room temperature offset documented on each unit. Note: See page 202 for thermistor table. APPLICATIONS • VAV reheat boxes • Dual duct boxes • Fan coils • Prove that hot water valve or electric heat is functioning properly • Check individual reheating stages • Check for hot water valve leaks • Determine if damper actuators are functioning on dual duct boxes Easy installation Stainless steel duct probe with mounting flange Two wires 2-wire installation (optional quick disconnect)…installs in minutes VAV systems Installation-ready for VAV systems and plenum areas … saves money on job commissioning and warranty service Plenum rated Plenum rated cable standard Application flexibility 4” or 8” (102 mm or 204 mm) duct probes SPECIFICATIONS TM Temperature Monitoring | VAV Discharge Temperature Sensors TJ SERIES VAV Discharge Air Sensor for Reheat Applications HQ0001880.H 0117L 0.25" (6.3 mm) Optional 1/4” female quick disconnect 1.5" (38 mm) 2.0" (51 mm) 1.1" (28 mm) 1.0" (26 mm) Sensor Type Option Probe Length “L” B = 100R platinum, RTD C = 1k platinum, RTD D = 10k T2, Thermistor E = 2.2k, Thermistor F = 3k, Thermistor G = 10k CPC, Thermistor H = 10k T3, Thermistor I = 1k Balco (Nickel-iron) RTD J = 10k Dale, Thermistor K = 10k w/11k shunt, Thermistor M = 20k NTC, Thermistor N = 1800 ohm, Thermistor P = 10mV/°C, Linitemp R = 10k US, Thermistor S = 10k 3A221, Thermistor T = 100k, Thermistor U = 20k “D”, Thermistor W = 10k T2 high accuracy, Thermistor Y = 10k T3 high accuracy, Thermistor B = 4"(102mm) D = 8"(204mm) TJ 0 = Standard 5 ft. cable, No QDs 1 = 1/4" Female Quick Disconnects (QD) 2 = 1/4” QDs with 8 ft. leadwires 3 = 10 ft. cable, no QDs Output = Resistive0 = None 1 = 1-point cal validation* 2 = 2-point cal validation* Example: TJBDR21 R Cal Certificate ORDERING INFORMATION DIMENSIONAL DRAWING *Not available with W and Y high-accuracy thermistors. Temperature Monitoring | TJ Series HQ0001880.H 0117Next >