Z205467-0F Page 1 of 2 ©2019 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 0319 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. Other companies’ trademarks are hereby acknowledged to belong to their respective owners. NOTICE • This product is not intended for life or safety applications. • Do not install this product in hazardous or classied locations. • Read and understand the instructions before installing this product. • Turn o all power supplying equipment before working on it. • The installer is responsible for conformance to all applicable codes. If this product is used in a manner not specied by the manufacturer, the protection provided by the product may be impaired. No responsibility is assumed by the manufacturer for any consequences arising out of the use of this material. Installation Guide Temperature TM Product Identification Product Overview TD, TF, and TG temperature sensors monitor the temperature of the air inside a duct. The probe is available in multiple lengths to suit multiple applications. All models have standard resistive outputs compatible with building control systems, and all models are warranted for a period of five years. TD/TF/TG Series Duct Mounted Temperature Sensors Specifications Wiring 22 AWG; 2-wire RTD/Thermistor Housing Stainless Steel Mounting Location Not suitable for wet locations. For indoor use only. WARRANTY Limited Warranty 5 years COMPLIANCE INFORMATION Agency Approvals CE TF TD TG T EnclosureProbe Length B = 4" (102 mm) C = 6" (152 mm) D = 8” (203 mm) E = 12” (305 mm) F = 18” (457 mm) K = 36” (914 mm) D = Duct F = Duct w/ mounting box G = Duct w/ water resistant housing Cal Certificate 0 = None 2 = 3-point NIST calibration Sensor TypeOutput = ResistiveB = 100R platinum, RTD C = 1k platinum, RTD D = 10k T2, Thermistor E = 2.2k, Thermistor F = 3k, Thermistor H = 10k T3, Thermistor I = 1k Balco (Nickel-iron) RTD J = 10k Dale, Thermistor K = 10k w/11k shunt, Thermistor M = 20k NTC, Thermistor N = 1800 ohm, Thermistor T = 100k, Thermistor W = 10k T2 high accuracy, Thermistor Y = 10k T3 high accuracy, Thermistor RØZ205467-0F Page 2 of 2 ©2019 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com 0319 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. Other companies’ trademarks are hereby acknowledged to belong to their respective owners. TD/TF/TG Series Installation Guide TM Dimensions TD Model 0.25"Dia. (6 mm) 1.5" (38 mm) 2" (51 mm) 1.1" (28 mm) L TF Model Available in 4”, 6”, 12” and 18” probe lengths 4.20” (106.68 mm) 1.78” (45.18mm) 3.88” (98.60 mm) TG Model L 0.25"Dia. (6.3 mm) 2.9" (74 mm) 4.6" (117 mm) 2.0" (51 mm) 0.7" (18 mm) Foam Gasket 2.5" x 2.5" (64 mm x 64 mm) 1. Drill a 3/8” diameter hole into a duct for the sensor probe. 2. Insert the probe into the duct. 3. Secure the junction box housing (TF/TG) or the mounting flange (TD) to the outer surface of the duct using the self-tapping screws provided. 4. Wire as shown. Thermistor RTD InstallationNext >