Installation Instructions Notice d’installation Instrucciones de montaje Document No. 129-541 April 2, 2013 OpenAir® GNP/GAP Series Rotary Fail-Safe and Fail-in-Place Rotatif avec position de repli et sans RAZ A prueba de averías rotatorio y Dejar-en-Lugar A Contents Contenu Contenido a b j e g f d c EA0892R1 a. Actuator b. Self-centering shaft adapter c. Position indicator d. Shaft adapter locking clip e. Position indicator adapter f. Mounting bracket g. Mounting screws j. Auxiliary switch adjustment tool Item Number 129-541, Rev. FA Page 1 of 10 Hints/Warnings Indications/Mises en garde Indicaciones/Consejos Keep this instruction guide together with the actuator or with the plant documentation! ¡Conserve las instrucciones con el accionador o con la documentación de la planta! Cette notice est à conserver avec le servomoteur ou avec la documentation de l’installation! Warning Avertissement ! Precaución Do not open the actuator ! Ne pas ouvrir le servomoteur ! No abra el accionador ! Do not expose the actuator’s connecting cables to water or lay the cables in water. Les câbles de raccordement du servomoteur ne doivent pas entrer en contact avec l'eau. No exponer los cables de conexión del actuador al agua ni dejarlos en contacto con ésta. Device of protection class II (protective insulation) Classe d'isolation II (isolation de protection) Equipo con tipo de protección II (aislamiento protegido) Classe d'isolation III (isolation de protection) Device of protection class III (protective insulation) Equipo con tipo de protección III (aislamiento protegido) Posicionamiento manual del actuador Sólo debe accionarse después del montaje del adaptador del eje y el indicador de posición, según las secciones C1 y C2. Manual override of the actuator Only allowed after mounting of shaft adapter and position indicator, according to section C1 and C2. Positionnement manuel du servomoteur Ne doit être actionné qu’après le montage de l’adaptateur d’axe et de l’indicateur de position, selon les sections C1 et C2. Wiring and commissioning Wiring and commissioning Raccordement et mise en route Para más información, véase la hoja de instrucciones técnicas GNP/GAP 155-771. Additional information is found in Technical Instructions GNP/GAP 155-771. Pour tout renseignement supplémentaire, consulter la fiche technique GNP/GAP 155-771 NOTE: Mark the rotation and power-fail direction of the damper on the ductwork before beginning the installation or removing the existing actuator. NOTE: Marquez la rotation et la direction en cas de panne de courant sur le registre du system de gaines avant de commencer l'installation ou d’enlever le servomoteur existant. NOTA: Marque la rotación y la dirección power-fail del apagador en la canalización antes de comenzar la instalación o de quitar el actuador existente. B Mounting Position Position de montage Posición de montaje EA1045R3 < 45 < 45 90 ASK75.3U ASK75.3U IP 54NEMA 3R Figure 1. Document No. 129-541 Installation Instructions April 2, 2013 Page 2 of 10 Siemens Industry, Inc. C Adapter Mounting Montage de l’adaptateur Montaje del adaptador 90° 90° 1 EA1276R1 Figure 2. Determine Rotation Direction. C1 Clockwise to Open Ouvrir dans le sens des Abrir en dirección de las aiguilles d'une montre agujas del reloj click ! 2 , ° 5 0° 6' 7' 5' d b e a 90° 90° 90° 9 0° 8' 4' Marquage de Marca de Montaje positionnement Mounting mark EA0894R2 > 2.44 (> 62 mm) ≥ 0.75 ≤ 2.44 (≥ 19 mm ≤ 62 mm) PushPush PushPush Figure 3. Clockwise to Open. Document No. 129-541 Installation Instructions April 2, 2013 Siemens Industry, Inc. Page 3 of 10 C2 Counterclockwise to Open Ouvrir dans le sens inverse Abrir en dirección con- des aiguilles d'une montre traria a las agujas del reloj Push Push 90° 5' d 7' d c b 6' e 10' 9' 8' a a b c 90° 90° 90° 90° 90°90° 90° 87,5° 2,5° 0° Marquage de positionnement Mounting mark Marca de Montaje EA0895R2 > 2.44 (> 62 mm) ≥ 0.75 ≤ 2.44 (≥ 19 mm ≤ 62 mm) PushPush PushPush Figure 4. Counterclockwise to Open. C3 Limits for Angular Rotation Limites de l’angle de rotation Límites de rotación angular 2 1 d c 0º ... 15º 10º 5º 0º EA1282R1 X=5° X=Steps Figure 5. Limiting Angular Rotation. Document No. 129-541 Installation Instructions April 2, 2013 Page 4 of 10 Siemens Industry, Inc. C4 Shaft Mounting Montage sur l’axe du volet Montaje sobre el eje f 6 5 2 3 3' 4 4' 1 g f EA0884R2 10 mm 10 mm EA0899R1 60 - 90 lb-in (7 - 10 Nm) 60 - 90 lb-in (7 - 10 Nm) Figure 6. Shaft Mounting. Document No. 129-541 Installation Instructions April 2, 2013 Siemens Industry, Inc. Page 5 of 10 D Manual Override Positionnement manuel Reposición manual Push Push 3 2 2' 3 1 EA0900R1 Figure 7. Manual Override. Setting: Auxiliary E Réglage: Contacts Ajuste: Contacto Auxiliar Switches A, B Auxiliaires A, B A, B EA1281R1 A B b S1S1S4S4 S2S3S2S3S5S6S5S6 B A Factory setting Préreglé à l'usine Ajuste de fábrica A = 5° B = 85° (Q11)(Q11) (Q12)(Q14)(Q12)(Q14) (Q11)(Q11) (Q12)(Q14)(Q12)(Q14) Figure 8. Setting Auxiliary Switches. For setting auxiliary switches see Technical Instructions 155-771. Réglage des contacts auxiliaires : voir la notice technique 155-771. Para ajustar los conmutadores auxiliares consultar la hoja de Instrucciones Técnicas 155-771. Document No. 129-541 Installation Instructions April 2, 2013 Page 6 of 10 Siemens Industry, Inc. F1 DIP Switches Communtateur DIP DIP Contacto NOTE: ● The black position indicates the active switch setting. ● For Siemens FHC/LRC pulsed control signal applications, see Section F2. ● On initial power-up, and after a power-fail event, the GNP actuators require up to 90 seconds to fully charge their capacitors. During this time the actuator will respond to positioning commands, but will not power-fail until the capacitors are fully charged. Rotation Direction EA1289R1 Power Fail Direction GNP19.... Only Modulating Control2-Position ControlFloating Control 0 to 10Vdc2 to 10Vdc0 to 20mA4 to 20mA Figure 9. Setting. EA1291R1 Figure 10. Siemens Factory Default Setting. NOTE: An improperly tuned loop will cause excessive repositioning that will shorten the life of the actuator. NOTE: Une boucle mal réglée va entrainer des repositionnements excessifs qui réduiront la vie du servomoteur. NOTA: Un circulo entunado incorrectamente causara reposiciones excesivas que acortaran la vida del actuador. Document No. 129-541 Installation Instructions April 2, 2013 Siemens Industry, Inc. Page 7 of 10 Siemens FHC/LRC Siemens FHC/LRC signal Siemens FHC/LRC pulsó F2 Pulsed Control Signal de commande pulsé senal de control EA1294R1EA1295R1 Actuator Action Wire 7 (Orange) Wire 8 (Gray) Wire 7 (Orange) Wire 8 (Gray) Rotate clockwise 24V 24V — — Rotate counterclockwise — — 24V 24V Hold position 24V — 24V — Hold position — 24V — 24V EA1296R1 M AB 2 9S2S3S5S6 1 8 7 S1S4 Feedback (0 to 10 Vdc) Common Control Signal 24 Vac/dc 24 Vac to 250 Vac 12 to 30 Vdc Supply (24 Vac/dc) Red Black Gray Pink Black/Red Black/PinkBlack/Blue Gray/Red Gray/PinkGray/Blue Orange Figure 11. Pulsed Control Signal. CAUTION: Unused wires must be properly terminated. Les fils inutilisés doivent être correctement bouclés. Los alambres inusitados deben ser terminados correctamente. Document No. 129-541 Installation Instructions April 2, 2013 Page 8 of 10 Siemens Industry, Inc. G Wiring diagrams Schémas de raccordement Diagramas de cableado CAUTION: Unused wires must be properly terminated. Les fils inutilisés doivent être correctement bouclés. Los alambres inusitados deben ser terminados correctamente. EA1286R2 M Feedback (0 to 10 Vdc) Common Control Signal 24 Vac/dc 29S2S3S5S6 17S1S4 24 Vac to 250 Vac 12 to 30 Vdc Supply (24 Vac/dc) Red Black Orange Pink Black/Red Black/PinkBlack/Blue Gray/Red Gray/PinkGray/Blue 2-position control Commande TOR Control a 2 puntos NOTE: 2-position control requires three wires. REMARQUE : La commande TOR exige trois fils. NOTA : El control de 2 posiciones requiere tres alambres Figure 12. Two-Position Control. EA 12 7 8 R 1 M AB 2 9S2S3S5S6 1 8 7 S1S4 Feedback (0 to 10 Vdc) Common Control Signal 24 Vac/dc 24 Vac to 250 Vac 12 to 30 Vdc Supply (24 Vac/dc) Red Black Gray Pink Black/Red Black/PinkBlack/Blue Gray/Red Gray/PinkGray/Blue Orange Floating control Commande à action flottante Control de flotación Figure 13. Floating Control. EA1279R1 M Feedback (0 to 10 Vdc) Common 0(2) to 10 Vdc 0(4) to 20 mA 29S2S3S5S6 18S1S4 24 Vac to 250 Vac 12 to 30 Vdc Supply (24 Vac/dc) Control Signal Red Black Gray Pink Black/Red Black/PinkBlack/Blue Gray/Red Gray/PinkGray/Blue Modulating control Commande progressive Control continuo Figure 14. Modulating Control. Document No. 129-541 Installation Instructions April 2, 2013 Siemens Industry, Inc. Page 9 of 10 G Wiring diagrams, continued Schémas de raccordement, suite Diagramas de cableado Table 1. Wire Designations. Connecting Standard Symbol Function Color Color Symbol 1 Supply Red RD 2 Common Black BK 7 2-position control signal Floating (CCW) Control signal Orange OG 8 Modulating: 0(2) to10 Vdc / 0 (4) to 20 mA Floating: (CW) Control signal Gray GY 24 Vac/dc Actuator 9 Feedback: 0 to 10 Vdc Pink PK S1 Switch A Common Gray/red GYRD S2 Switch A N.C. Gray/blue GYBU S3 Switch A N.O. Gray/pink GYPK S4 Switch B Common Black/red BKRD S5 Switch B N.C. Black/blue BKBU Auxiliary Switches S6 Switch B N.O. Black/pink BKPK Table 2. Désignations de fil. Câbles de raccordement Symbole Standard Fonction Couleur Couleur Abbreviation 1 Alimentation Rouge RD 2 Commun Noir BK 7 Signal de commande TOR Signal de la commande (CCW) de flottement Orange OG 8 Modulant: Signal de commande 0(2)…10 V / 0 (4) 4 à 20 mA Flottement : (CW) Signal de commande Gris GY Servomoteur 24 V~/- 9 Rétrocation: 0…10 V- Rose PK S1 Commutateur A Commun Gris/rouge GYRD S2 Commutateur A N.F. Gris/bleu GYBU S3 Commutateur A N.O. Gris/rose GYPK S4 Commutateur B Commun Noir/rouge BKRD S5 Commutateur B N.F. Noir/bleu BKBU Commutateurs auxiliaires S6 Commutateur B N.O. Noir/rose BKPK Table 3. Designaciones del alambre. Conexión Símbolo estándar Función Color Color Abreviatura 1 Suministro de corriente Rojo RD 2 Común Negro BK 7 Señal de control - sentido contrario a las agujas del reloj (para el control de flotación) Orange OG 8 Modulación: Señal de entrada 0(2) a 10 V / 0 (4)4 a 20 mA Control de flotación: Señal de control Gris GY Accionador 24V ca/cc 9 Feedback: 0 to 10 Vdc Rosado PK S1 Conmutador A Común Gris/rojo GYRD S2 Conmutador A N.C. Gris/azul GYBU S3 Conmutador A N.A. Gris/rosado GYPK S4 Conmutador B Común Negro/rojo BKRD S5 Conmutador B N.C. Negro/azul BKBU Conmutadores auxiliares S6 Conmutador B N.A. Negro/rosado BKPK P1 Potenciómetro de realimentación 0 a 100% P1 - P2 Blanco/rojo WHRD P2 Potenciómetro de realimentación común Blanco/azul WHBU Indicador de posición P3 Potenciómetro de realimentación 100 a 0% P3 - P2 Blanco/rosado WHPK Document No. 129-541 Installation Instructions April 2, 2013 Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. OpenAir is a registered trademark of Siemens Scheiwz AG. Other product or company names mentioned herein may be the trademarks of their respective owners. © 2012 Siemens Industry, Inc. Les informations contenues dans ce document sont basées sur les caractéristiques les plus récentes. Nous nous réservons le droit de modifier ces caractéristiques, de même que les modèles, en fonction des évolutions techniques. OpenAir est une marque déposée de Siemens Schweiz AG. Tout autre nom de produit ou de société mentionné dans ce document peut être la marque de son propriétaire respectif. © 2012 Siemens Industry, Inc. Este documento ha sido preparado en base a especificaciones actuales. La compañía se reserva el derecho de modificar las especificaciones, así como los modelos, a medida que se incorporen nuevas mejoras técnicas. OpenAir es marca registrada de Siemens Schweiz AG. Los nombres de otros productos o compañías aquí mencionados serán las marcas de sus respectivos propietarios. © 2012 Siemens Industry, Inc. Siemens Industry, Inc. Building Technologies Division 1000 Deerfield Parkway Buffalo Grove, IL 60089 USA + 1 847-215-1000 Your feedback is important to us. If you have comments about this document, please send them to sbt_technical.editor.us.sbt@siemens.com Document No. 129-541 Printed in the USA Page 10 of 10 H Dimensions Encombrement Dimensiones min. 1/2 (12) 5-9/16 (141) 8-3/8 (212) 1-11/16 (42) 1-3/16 (30) 1-3/16 (30) 1/8 (3) min. 4 (100) min. 6 (150) min.2-3/8 (60) min. 4 (100) EA0877R2 3 ft (900) 2-3/8 (60) 1/2" NSPT 1/2 (12) 3/4 (19) 47.5˚47.5˚ min. 4 (100) 3.25 (83) 25/32 (20) 7-1/16 (180) Ø 3/16 (Ø 5) EA0876R1 Figure 15. GNP/GAP Actuator in Inches (Millimeters). Next >