Siemens Industry, Inc. Flowrite TM AP 599 Series Technical Instructions Document No. 155-161P25 AP 599-1 June 14, 2019 8-inch Pneumatic Valve Actuator Description The Flowrite AP 599 Series 8-inch pneumatic valve actuator is designed for use with the Flowrite VF 599 Series valves with a 3/4-inch (20 mm) stroke. This actuator is available with two diaphragm options. Features • Completely enclosed actuator housing protects the diaphragm, spring, and start point adjuster. • Positioning relay is available factory mounted or as an accessory. • Start point of the actuator spring is adjustable. This allows the valve to be sequenced. • Easy installation. Application These 8-inch actuators are designed to be used on Flowrite VF 599 Series valves in liquid service and steam service applications. Product Numbers Table 1. Product Numbers Actuator Codes 8-inch Pneumatic 8-inch Pneumatic with Factory Mounted Positioner 599-01050 Normal Duty 277 283 599-01051 High Temperature 278 284 Technical Instructions Flowrite™ 8-inch Pneumatic Valve Actuator Document Number 155-161P25 June 14, 2019 Page 2 Siemens Industry, Inc. Warning/Caution Notations WARNING: Personal injury/loss of life may occur if a procedure is not performed as specified. CAUTION: Equipment damage, or loss of data may occur if the user does not follow a procedure as specified. Specifications Effective diaphragm area 28 inches2 (180 cm2) Operating Temperatures Normal duty service – media temperatures Buna-N 25°F to 300°F (–4°C to 149°C) High temperature service – media temperatures Silicone rubber 25°F to 366°F (–4°C to 186°C) Ambient operating and storage temperature 35°F to 180°F (2°C to 85°C) Operating Nominal spring range Fixed span Normal duty service 5 psi (34 kPa) High temperature service 10 psi (68 kPa) Adjustable start point 3 to 10 psi (21 to 69 kPa) Factory setting 3 to 8 psig (21 to 55 kPa) NO valves 10 to 15 psig (69 to 103 kPa) NC valves Nominal stroke 3/4-inch (20 mm) Maximum diaphragm pressure 35 psi (241 kPa) Air Connection 1/8-inch NPT Miscellaneous Mounting location NEMA 1 (interior only) Dimensions 14-1/8-in H x 8-3/4-in diameter (359 mm H x 222 mm diameter) Shipping weight 8.7 lbs. (4 kg) Accessories Stem Heating Element ASZ6.6 Positioning Relay and Mounting Kit 599-00426 Instructions for mounting are included with the accessory. Spring Clamp (secures 1/4-inch O.D. polytubing to barb-fitting 531-833 at higher control pressures or elevated temperatures) Service Kits Diaphragm replacement kit (package of one) Normal duty 599-01060 High temperature service 599-01061 Stem adapter kit for 8-inch Pneumatic Actuator 599-00435 Stem retainer kit 599-10048 Actuator Retainer Kit 599-00436 Flowrite™ 8-inch Pneumatic Valve Actuator Technical Instructions Document Number 155-161P25 June 14, 2019 Siemens Industry, Inc. Page 3 Operation The control air signal upon the diaphragm causes the valve to modulate whenever the air pressure is within the spring range of the actuator. The actuator spring provides the necessary force to hold the stem in the stem up (direct acting) position. Mounting and Installation Allow 12 inches (300 mm) headroom and six inches (150 mm) on either side for servicing the actuator. For best performance install the actuator vertically above the valve. The actuator may be installed in any position between vertical and horizontal. Siemens Building Technologies does not recommend installing the actuator below horizontal or up side down. See Figure 1 for allowable mounting positions. Complete instructions for field mounting the actuator are included with the actuator. The top edge of the stem nut indicates the valve stem position. The “0” marking on the actuator yoke indicates stem up position. The “1” mark indicates stem down position. See Figure 2. Figure 1. Acceptable Mounting Positions. Service Diaphragm Replacement Complete instructions are included in the diaphragm replacement kit. WARNING: Relieve spring tension before removing the actuator upper housing. Technical Instructions Flowrite™ 8-inch Pneumatic Valve Actuator Document Number 155-161P25 June 14, 2019 Page 4 Siemens Industry, Inc. Spring Adjustment With the actuator in an upright position and the stem visible as shown in Figure 2, use a 3/4-inch (.75 mm) open end wrench to turn the adjustment screw. • Normally Open Valves: To increase the start to close pressure, turn the adjustment screw from right to left. To decrease, turn the adjustment screw from left to right. • Normally Closed Valves: To increase the start to open pressure, turn the adjustment screw from right to left. To decrease, turn the adjustment screw from left to right. NOTE: As the line pressure differential across the valve increases, the spring span decreases. Figure 2. Spring Adjustment. Flowrite™ 8-inch Pneumatic Valve Actuator Technical Instructions Document Number 155-161P25 June 14, 2019 Siemens Industry, Inc. Page 5 Parts of the 8-inch Actuator Figure 3. Flowrite AP 599 Series 8-inch Pneumatic Valve. Item Description Qty Material Item Description Qty Material 1 Upper housing 1 Aluminum 11 1/4-20 external tooth lock washer 2 Plated Steel 2 Diaphragm (Normal duty) (High temperature) 1 Neoprene silicone 12 1/4-20 hex head cap screw 2 Plated Steel 3 3/8 x 24 hex nut 1 Plated steel 13 5/16-18 thread forming screws 6 Plated Steel 4 Piston plate 1 Aluminum 14 Spring 1 Chrome Van. Steel 5 Adjust. Screw Ass’y 1 Steel and bronze 15 Spring seat 1 Carbon Steel 6 Thrust washer 1 Carbon steel 16 Lower housing 1 Aluminum 7 Actuator shaft 1 Plated steel 17 Jam nut 1 Plated Steel 8 Stem adapter 1 Plated steel 18 Actuator retainer 1 Aluminum 9 Stem retainer clip 1 Stainless steel Diaphragm replacement kit Normal duty High temperature Item 2 599-01060 599-01061 10 Stem nut 1 Stainless steel Stem retainer kit (One each of items 9 and 10) 599-10048 Stem adapter kit (items 8,9,10, and 17) 599-00435 Actuator retainer kit ( items 11, 12, and 18) 599-00436 Technical Instructions Flowrite™ 8-inch Pneumatic Valve Actuator Document Number 155-161P25 June 14, 2019 Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. Flowrite is a trademark of Siemens Industry, Inc. Products or company names mentioned herein may be the trademarks of their respective owners. © 2019 Siemens Industry, Inc. Siemens Industry, Inc. Smart Infrastructure 1000 Deerfield Parkway Buffalo Grove, IL 60089 + 1 847-215-1000 Your feedback is important to us. If you have comments about this document, please send them to sbt_technical.editorus.sbt@siemens.com Document No. 155-161P25 Printed in the USA Page 6 Dimensions Figure 4. Dimensions in Inches (Millimeters). Next >