www.schneider-electric.com S1A53832 Important information XXXXXX Altivar 212 Variable speed drives for asynchronous motors Installation manual 01/2011Important information 2S1A53832 01/2011 The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us. No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of Schneider Electric. All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to help ensure compliance with documented system data, only the manufacturer should perform repairs to components. When devices are used for applications with technical safety requirements, the relevant instructions must be followed. Failure to use Schneider Electric software or approved software with our hardware products may result in injury, harm, or improper operating results. Failure to observe this information can result in injury or equipment damage. © 2011 Schneider Electric. All rights reserved.3 Table of content Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 About the book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Chapter 1Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Reference description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Chapter 2Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Chapter 3Steps for setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Steps for setting up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Chapter 4Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 ATV212H dimensions and weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ATV212W dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Electrical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Connection diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Examples of recommended circuit diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Chapter 5Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Drive mounting generalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Specific recommendations for mounting in an enclosure. . . . . . . . . . . . . . . . . . . . .36 Position of the charging LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Opening the drive to access terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Wiring recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Power terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Control terminals and switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Installing option card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Use on an impedance grounded (IT) system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Recommended branch circuit protection devices. . . . . . . . . . . . . . . . . . . . . . . . . . .59 Chapter 6Migration ATV21 --> ATV212 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Generalities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Differentiating points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Terminal and switches arrangement comparison. . . . . . . . . . . . . . . . . . . . . . . . . . .634S1A53832 01/2011S1A53832 01/20115 § Safety Information Important Information NOTICE Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. PLEASE NOTE The word "drive" as used in this manual refers to the controller portion of the adjustable speed drive as defined by NEC. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this product. © 2010 SchneiderElectric. All Rights Reserved. The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists, which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a potentially hazardous situation, which, if not avoided, can result in death, serious injury or equipment damage. CAUTION CAUTION indicates a potentially hazardous situation, which, if not avoided, can result in injury or equipment damage. CAUTION CAUTION, used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, can result in equipment damage.6S1A53832 01/2011S1A53832 01/20117 At a Glance Document Scope The purpose of this document is: z to give you mechanical and electrical information related to the ATV212 drive, z to show you how to install and wire this drive. Validity Note This documentation is valid for the Altivar 212 drive. Related Documents You can download the latest versions of these technical publications and other technical information from our website at www.schneider-electric.com. Title of DocumentationReference Number ATV212 Quick StartS1A53825 ATV212 Programming manualS1A53838 ATV212 Modbus manualS1A53844 ATV212 BACnet manualS1A53845 ATV212 Metasys N2 manualS1A53846 ATV212 Apogee FLN P1 manualS1A53847 ATV212 LonWorks manualS1A53848 About the book8S1A53832 01/20119S1A53832 01/2011 Introduction 1 Introduction What's in this Chapter? This chapter contains the following topics: TopicPage Device overview10 Reference description11Next >