Refer to the QuickLIT website for the most up-to-date version of this document.VG7000 Series Bronze Control Valves Product Bulletin1VG7000 Series Bronze Control Valves are designed primarily to regulate the flow of water and steam in response to the demand of a controller in Heating, Ventilating, and Air Conditioning (HVAC) systems. These valves are available in Normally Open (N.O.), Normally Closed (N.C.), and three-way mixing configurations. Both electric and pneumatic actuators are available for factory or field mounting. Figure 1: VG7000 Series Bronze Control ValvesTable 1: Features and BenefitsFeaturesBenefitsComplete Family of 1/2through 2in. Bronze Valves, Brass and Stainless Steel Trim, with Several Styles of Electric and Pneumatic ActuatorsOffers a broad selection to choose from, including electric spring return actuators, a true 1-1/4 in. valve body, a 3/4 in. valve with small oval top actuator, and Stainless Steel (SS) trim capable of 100 psig (690 kPa) saturated steam.Flexible Features and Options Ordering MatrixSuits your specific application viathousands of easy-to-select, factory-assembled combinations.Standard JohnsonControls® RingPack PackingsProvides industry-leading reliability and operating life.Testing for Tight Shutoff of Every ValveProvides energy conservation and ensures occupant comfort.Standard Bonnet and StemDesignAllows easy field retrofit, easy field mounting, and interchangeability of actuators with the use of standardized mounting kits.VG7000 Series Bronze Control ValvesProduct BulletinVG7000 SeriesCode No. LIT-977140Issued December 2018Supersedes November 15, 2013This product is made of copper alloy, which contains lead. The product is therefore not to be used on drinking water.This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more infor-mation, go to www.P65Warnings.ca.gov.WARNING: BRASS MAY CONTAIN LEADTo fulfill our obligations towards Article 33, in accordance to the European REACH Regulation No 1907/2006 EC, we hereby inform you that this article contains the following Substances of Very High Concern mentioned on the Candidate list: • LeadVG7000 Series Bronze Control Valves Product Bulletin2Ordering Data Table 2: Ordering Data — VG7000 Series Bronze Control Valves1VGValve Global127Product Family7 = Cast Bronze32Body Type2 = Two-Way, Normally Open/Push-Down-to-Close44 = Two-Way, Normally Closed/Push-Down-to-Open5 = Two-Way Angle, Normally Open/Push-Down-to-Close8 = Three-Way Mixing4End Connections4 = Threaded National Pipe Thread (NPT)55 = Union Globe/Union Angle (1/2 through 1-1/2 in. Body Sizes, PDTC Only, Brass Trim Valves Only))7 = Union Sweat, 3/8 in. Tubing (1/2 in. Body Size Only, Brass Trim Valves Only))8 = Union Sweat, Standard Tubing (Brass Trim Valves Only)9 = Union Sweat, 3/4 in. Tubing (1/2 in. Body Size Only, Brass Trim Valves Only))1Trim and Flow Characteristics1 = Brass Equal Percentage (All Two-Way and 1/2 in. Three-Way)62 = Brass Linear (Three-Way Only)3 = Stainless Steel Equal Percentage (Two-Way Only)4 = Stainless Steel Linear (Three-Way Only)LSize and Cv (Kv)C = 1/2 in., 0.73 Cv (0.63 Kv)7E = 1/2 in., 1.8 Cv (1.6 Kv)G = 1/2 in., 4.6 Cv (4.0 Kv)L = 3/4 in., 7.3 Cv (6.3 Kv)N = 1 in., 11.6 Cv (10.0 Kv)P = 1-1/4 in., 18.5 Cv (16.0 Kv)R = 1-1/2 in., 28.9 Cv (25.0 Kv)S = 2 in., 46.2 Cv (40.0 Kv)TStem TypeT = Standard Threaded Stem (All Except V-3801, MP84, VA-8x2x)8S = Slotted Stem and Small Bonnet (Factory-Mounted V-3801, VA-8x2x Only; Only Brass Trim Valves)M = Large Threaded Stem (Factory-Mounted MP84 Only, Only Stainless Steel Trim Valves)+Actuator Mounting+ = Factory-Mounted Actuator (See Table3 and Table4.)9(Leave Fields 9 through 15 blank for valve without factory-mounted actuator. Valve without factory-mounted actuator is available with standard threaded stem only.)123456789101112131415 = FieldVG7241LT+Example: Cast bronze valve, two-way, normally open/push-down-to-close, threaded (NPT) end connections, brass trim, equal percentage, 3/4 in., 7.3 Cv, standard threaded stem.Valve+Actuator1.See Table3 when adding a factory-mounted pneumatic actuator to a valve body. See Table4 when adding a factory-mounted electric actuator to a valve body. For valid valve and actuator combinations, see Table16 and Table17.VG7000 Series Bronze Control Valves Product Bulletin3Table 3: Ordering Data — Adding a Factory-Mounted Pneumatic Actuator1VG7243LT+3008V-3000/V-3801Pneumatic Actuator23801 = V-3801-8001 Small Oval Top (Slotted Stem Only, Brass Trim Valves Only, Must be Factory Assembled)123456789101112133008 = V-3000-8012 Exposed3003 = V-3000-8003 EnclosedBSpring Range(V-3000/V-3801)B = 3 to 6 psig (Suggested for N.O. Valves with Positioner)14D = 4 to 8 psig (Suggested for Three-Way Valves with Positioner)E = 9 to 13 psig (Suggested for N.C. Valves with Positioner)PAccessories(V-3000/V-3801)P = V-9502 Positioner (Not Available with V-3801-8001 or V-3000-8003)15Blank = None82MP8000 SeriesPneumatic Actuator282 = MP82, 25 sq in. Spring-Return-Up (SS or Brass Trim)101184 = MP84, 50 sq in. Spring-Return-Up (SS Trim Only)(Only spring-return-up models of MP8000 Series Pneumatic Actuators are available factory-mounted to VG7000 Series Bronze Control Valves.)1Stroke(MP8000 Series)1 = 5/16 in. (1/2 or 3/4 in. Valves with MP82 Actuator Only)122 = 1/2 in. (1 or 1-1/4 in. Valves with MP82 Actuator Only)3 = 3/4 in. (1-1/2 or 2 in. Valves with MP82 or MP84 Actuator)CSpring Range(MP8000 Series)C = 3 to 7 psig (Suggested for N.O. Valves with Positioner)13D = 4 to 8 psig (Suggested for Three-Way Valves with Positioner)E = 9 to 13 psig (Suggested for N.C. Valves with Positioner)01Accessories(MP8000 Series)00 = None141501 = V-9502 Positioner123456789101112131415 = FieldVG7243LT+821C01Example: Cast bronze valve, two-way, normally open, threaded (NPT) end connections, stainless steel trim, equal percentage, 3/4 in., 7.3 Cv, standard threaded stem, MP82 Series Pneumatic Actuator, 5/16 in. stroke, 3 to 7 psig (21 to 48 kPa) spring range, with factory-mounted V-9502 Positioner.Valve+Actuator1.See Table2 when ordering a valve body only. See Table4 when adding a factory-mounted electric actuator to a valve body. For valid valve and actuator combinations, see Table16 and Table17.2.Refer to the actuator product bulletin or product/technical bulletin.VG7000 Series Bronze Control Valves Product Bulletin4Table 4: Ordering Data — Adding a Factory-Mounted Electric Actuator1VG7241LT+7150VA-7150/VA-7200Electric Actuator2, 37150 = VA-7150-1001 On/Off (Floating)123456789101112137152 = VA-7152-1001 Proportional, 0-10 VDC7153 = VA-7153-1001 On/Off (Floating), Feedback7200 = VA-7200-1001 On/Off (Floating)7202 = VA-7202-1001 Proportional, 0-10 VDC7203 = VA-7203-1001 On/Off (Floating), FeedbackGVoltage(VA-7150/ VA-7200)G = 24 VAC14Accessories(VA-7150/VA-7200)Blank = None15423VA-4233Electric Actuator2Spring Return Up101112423 = VA-4233-xGx-2, 24 VAC/VDCAGAFeatures(VA-4233)4AGA = Floating131415AGC = Floating, 2 Auxiliary SwitchesBGA = On/OffBGC = On/Off, 2 Auxiliary SwitchesGGA = Prop., 0-10 VDC, FeedbackGGC = Prop., 0-10 VDC, Feedback, 2 Auxiliary Switches92NVA7810VA7820/VA78305 Electric Actuator2,6Non-Spring Return10111271C = VA7810-xGx-2, 24 VAC/VDCSpring Return72C = VA7820-HGx-2, Spring-Return Stem Up 24 VAC74C = VA7830-HGx-2, Spring-Return Stem Down 24 VACGGAFeatures(VA78x0)7AGA = On/Off (Floating) (Available only with VA7810 Actuator)131415AGC = On/Off (Floating), 2 Auxiliary Switches(Available only with VA7810)HGA = Proportional, 0-10 VDC, FeedbackHGC = Proportional, 0-10 VDC, Feedback, 28020VA-8x2xElectric Actuator2,3, 88020 = VA-8020-1, On/Off (Floating)101112138122 = VA-8122-1, ProportionalGVoltage(VA-8x2x)G = 24 VAC14Accessories(VA-8x2x)Blank = None15123456789101112131415= FieldVG7241LT+8020GExample: Cast bronze valve, two-way, push-down-to-close, threaded (NPT) end connections, brass trim, equal percentage, 3/4 in., 7.3 Cv, standard threaded stem, VA-8020-1 On/Off (Floating) Electric Actuator, 24 VAC supply.Valve+Actuator1.See Table2 when ordering a valve body only. See Table3 when adding a factory-mounted pneumatic actuator to a valve body. For valid valve and actuator combinations, see Table16 and Table17.2.Refer to the actuator product bulletin or product/technical bulletin.3.Available only for PDTC Two-Way and Three-Way body styles.4.Available only for NPT (threaded) and Union Sweat End Connections body style.5.VA7830 actuator is available only on Three-Way Mixing body style.6.Available only for NPT (threaded) body style.7.VA7820 and VA7830 Proportional Control Actuators have selectable switches for field conversion to On/Off or Floating Control.8.Available only for 1/2 and 3/4 in. valves.VG7000 Series Bronze Control Valves Product Bulletin5Application OverviewVG7000 Series Bronze Control Valves feature brass and stainless steel trim, and are available in two-way configurations with Push-Down-to-Close (PDTC) (normally open if pneumatic or spring return) or Push-Down-to-Open (PDTO) (normally closed if pneumatic or spring return) with threaded (NPT), union sweat, union globe, and union angle end connections. The valve can be ordered with a variety of pneumatic actuators: V-3000-8012 (exposed, with or without a factory-mounted positioner), V-3000-8003 (enclosed), V-3801-8001 (oval top), and higher force MP8000 Series Actuators (with or without a factory-mounted pneumatic positioner).VG7000 Series Valves can also be ordered with any of the following series electric actuators: VA-4233, VA-7150, VA-7200, VA-8x2x, VA7810, VA7820, or VA7830. All electric actuators are fully compatible with JohnsonControls® controllers, reducing installation costs. Valves without actuators can be ordered with the standard bonnet and threaded stem design, allowing easy interchangeability of actuators with the use of standardized mounting kits. See Table2 through Table4 for ordering data and additional details. For valid valve and actuator combinations, see Table16 and Table17. The modulating valve plug of VG7000 Series Valves provides an equal percentage flow characteristic for two-way valves, and equal percentage or linear for three-way valves. Tight shutoff is ensured using a molded elastomeric disk in valves with brass trim, and a precisely machined metal-to-metal seat for valves with stainless steel trim. An arrow is cast on one side of the valve body indicating the direction of flow for proper piping.Pneumatic Actuator SelectionSee Table7, Table9, Table11, and Table16.Do not confuse the V-3000-8012, V-3000-8003, and V-3801-8001 Pneumatic Actuators with the V-3000-1, V-3000-2, and V-3802-1 Pneumatic Actuators. Refer to the V-3000-8011 (Exposed) and V-3000-8003 (Enclosed) Pneumatic Valve Actuators Product/Technical Bulletin (LIT-977252) for specifics regarding interchangeability. The V-3801-8001 is not a direct replacement for the V-3802-1 because V-3802-1 is not compatible with VG7000Series Valves.V-3801-8001 Pneumatic ActuatorThe V-3801-8001 is a low force, oval top actuator designed specifically for 1/2 and 3/4 in. valves where mounting space is restricted. The V-3801-8001 has sufficient force to handle most seating pressures, and the molded diaphragm design provides a constant effective area (4 sq in.) throughout the valve stem stroke. Due to the simplicity of the design, it is more economical to replace the actuator than repair it. The actuator assembly can be removed or repositioned by loosening a single set screw without disturbing the rest of the valve assembly.Because the V-3801-8001 uses a unique slotted valve stem for factory assembly (see the Stem Type section in Table2), the spring kits available are for field mounting to standard threaded stem valves. See Table7 for mounting kit code numbers.V-3000-8012 Pneumatic ActuatorThe V-3000-8012 is a versatile, medium-force pneumatic actuator that can be used in most HVAC applications, including sequential control of valves. See Table9 and Table11 for actuator sizing and selection.The permanently captured, molded rolling diaphragm of the V-3000-8012 provides a constant effective area (8 sq in.) throughout the valve stem stroke. The actuator assembly can be removed or repositioned by loosening a single set screw without disturbing the rest of the valve assembly.The V-9502 Pneumatic Positioner is also available for factory or field mounting to the V-3000-8012.V-3000-8003 Pneumatic ActuatorThe V-3000-8003, operationally similar to the V-3000-8012, is designed for enclosed installation in a location where the actuator might be subjected to tampering. The V-3000-8003 has a replaceable molded diaphragm design.IMPORTANT:The VG7000 Series Bronze Control Valves are intended to control saturated steam, hot water, and chilled water flow under normal equipment operating conditions. Where failure or malfunction of the VG7000 Series Valve could lead to personal injury or property damage to the controlled equipment or other property, additional precautions must be designed into the control system. Incorporate and maintain other devices, such as supervisory or alarm systems or safety or limit controls, intended to warn of or protect against failure or malfunction of the VG7000 Series Valve.VG7000 Series Bronze Control Valves Product Bulletin6MP8000 Series Pneumatic ActuatorsThe higher force MP82 (25 sq in. effective diaphragm area) and MP84 (50 sq in. effective diaphragm area) Pneumatic Actuators are used where higher maximum closeoff pressures are required, such as 1-1/2 and 2in. brass trim valves and 1/2 through 2 in. stainless steel trim valves.These actuators are equipped with a molded synthetic rubber diaphragm contained in a sturdy, carbon-steel housing that protects it against dirt and damage. The actuator can be easily removed to perform inline servicing to all parts of the valve. The MP8000 Actuators are available factory mounted or are easily field mounted to VG7000 Series Valves. See Table7 for the appropriate mounting kit.The MP8000 Actuators are designed to allow for reversing the action of the actuators in the field. If desired, the action of the MP8000 on Normally Open (N.O.) valves can be reversed from spring-return-up to spring-return-down or vice versa. To field reverse the actuator, refer to the MP8000 Pneumatic Valve Actuators Technical Bulletin (LIT-977258).The V-9502 Pneumatic Positioner is also available for factory or field mounting to MP8000 Series Pneumatic Valve Actuators.T-3000 Valve Top Thermostat ActuatorsThe T-3111 and T-3311 Series Valve Top Thermostat Actuators are available for field mounting to all VG7000 Series Valves (N.O., N.C., and three-way). The valve top thermostats are a combination of a pneumatic thermostat and a pneumatic valve actuator. The T-3111 and T-3311 are available in both direct and reverse acting models with various features and options. Refer to the T-3111 Integral Thermostat and Piston Top Valve Actuator Single Temperature, Single Pressure Product/Technical Bulletin (LIT-7171137) and the T-3311 Integral Thermostat and Piston Top Valve Actuator Dual Temperature, Dual Pressure Product/Technical Bulletin (LIT-7171152) for specifications and ordering information.Note:A mounting kit is required to field mount T-3111 or T-3311 Valve Top Thermostats to a valve. See Table7 for the appropriate mounting kit code number.Electric Actuator SelectionFactory-mounted electric actuators are available on two-way PDTC and three-way mixing valve configurations only. Actuators can be easily field reversed if required. The actuators can be field mounted on PDTO valves if desired. All proportional electric actuator assemblies are factory calibrated for nominal 0 to 10 VDC operation, to drive down with an increase in signal. The VA-4233 and VA78x0 are available on all valve styles: PDTO, PDTC, and three-way.VA-4233 Series Electric ActuatorsThe VA-4233 Series Electric Actuators use a stepper motor to accurately position the valve. In the event of a power failure, a spring in the actuator automatically returns the valve to the full stem-up position. These direct-mount, spring return electric actuators provide a minimum 61 lb force output for floating, on/off, or proportional control, and can be factory mounted to 1/2 through 1-1/4 in. valve bodies with NPT (threaded) and union sweat end connections.Integral auxiliary switches are available for indicating end stop position or to perform switching functions. On proportional models, position feedback is also available through a proportional DC voltage signal. All models feature a hand crank for manual positioning of the valve, independent of a power supply.VA-7150 Series Electric ActuatorsThe VA-7150 Series Actuators use a reversible synchronous motor and magnetic clutch to accurately position the valve. This non-spring return actuator has a 90 lb force output. The magnetic clutch maintains a constant load at the end of travel, ensuring tight valve shutoff and automatically compensating for seat wear.This actuator is available in three models: floating three-wire (VA-7150), floating with 0 to 2000 ohm feedback (VA-7153), or 0 to 10 VDC proportional control (VA-7152).VA-7200 Series Electric ActuatorsThe VA-7200 Series Actuators use a reversible synchronous motor and a magnetic clutch to accurately position the valve. This non-spring return actuator has a 180 lb force output. The magnetic clutch maintains a constant load at the end of travel, which ensures tight shutoff and automatically compensates for seat wear. This actuator is available in three models: floating three-wire (VA-7200), floating with 0 to 2000 ohm feedback (VA-7203), or 0 to 10VDC (0 to 20 mA) proportional control (VA-7202).VG7000 Series Bronze Control Valves Product Bulletin7VA-8x2x Series Electric ActuatorsThe VA-8x2x Series Actuators are synchronous motor-driven, force sensor limited, non-spring return actuators that feature a 22 lb seating force in a compact design. The VA-8020 accepts floating control from a three-wire, 24 VAC control signal. The VA-8122 typically accepts proportional control from a 0 to 10VDC control signal; however, it can be field adjusted to accept signals up to 20 VDC. In addition, the VA-8122 features an input signal reversing feature that allows it to be used in both heating and cooling applications.Note:The VA-8x2x is only available factory mounted on 1/2 and 3/4 in. valves. Because the VA-8x2x requires a unique slotted valve stem for factory assembly, it is necessary to select the S option in the Stem Type section of Table2.VA7810 Series Electric ActuatorsThe VA7810 Series is a line of motor driven, direct mount, non-spring return actuators that operate on 24VAC and are available for use with on/off (floating) or proportional controllers. The actuator is available factory mounted to 1/2 through 2 in. valve body styles with NPT (threaded) end connections with stainless steel trim and factory mounted to 1 through 2 in. valve body styles with NPT (threaded) end connections with brass trim. The actuator is available separately for field mounting to union sweat, union globe, and union angle VG7000 Series valves.The actuator delivers a minimum stem force of 180 lb. Integral auxiliary switches are available for indicating end-stop position or to perform switching functions. For proportional models a 0 (2) to 10 VDC signal feedback is available.VA7820/VA7830 Series Electric ActuatorsThe VA7820/VA7830 Series is a line of motor driven, direct mount, spring return actuators that operate on 24VAC. The actuators ship already set for 0 to 10 VDC Proportional control. With a simple change of DIP switch settings, the actuator can be reconfigured in the field for On/Off (Floating) Control. Position feedback is available via switches or a 0 (2) to 10VDC signal. The actuator delivers a minimum stem force of 180 lb. If the power fails, the automatic spring returns the valve stem up for the VA7820 actuator or the valve stem down for the VA7830 actuator. A manual override allows manual positioning of the valve when power is not available. The actuator is available factory mounted to 1/2 through 2 in. valve body styles with NPT (threaded) end connections with stainless steel trim and factory mounted to 1 through 2 in. valve body styles with NPT (threaded) end connections with brass trim. The actuator is available separately for field mounting to union sweat, union globe, and union angle VG7000 Series valves.VG7000 Series Bronze Control Valves Product Bulletin8Shipping Weights Table 5: Shipping Weights for Brass Trim Valves1ActuatorValve Weight, lb1/23/411-1/41-1/22V-3801-80012.53.1------------V-3000-80123.44.56.56.512.117.2V-3000-80033.24.36.36.211.917.0MP82------14.016.019.024.0MP84------------------VA-42335.36.48.48.3------VA-71503.95.07.06.912.617.7VA-7200------7.57.413.118.2VA-8x2x4.65.9------------VA7810------6.26.211.816.9VA7820/VA7830------7.97.913.518.61.Weights are approximate and based on the heaviest valve. Add 2 lb (0.9 kg) for pneumatic assemblies with a positioner.Table 6: Shipping Weights for Stainless Steel Trim Valves1ActuatorValve Weight, lb1/23/411-1/41-1/22V-3000-80123.74.56.98.9------V-3000-80033.54.26.78.7------MP8211.012.014.016.019.024.0MP84------------32.037.0VA-42335.35.68.010.0------VA-71503.94.26.68.612.617.7VA-72004.75.57.99.913.118.2VA78103.14.26.68.611.816.9VA7820/VA78304.85.98.310.313.518.61.Weights are approximate and based on the heaviest valve. Add 2 lb (0.9 kg) for pneumatic assemblies with a positioner.VG7000 Series Bronze Control Valves Product Bulletin9Field MountingA standard bonnet/stem design allows for easy field mounting of actuators. See Table2 to order valves without actuators; Table7, and Table8 to order the appropriate mounting kits; and Table16 and Table17 to identify compatible actuators. Refer to the appropriate actuator product bulletin for specific actuator code number information. Table 7: Field Mounting Kits for Pneumatic Actuators1Actuator StyleValve Size, in. (DN)2Spring Range psig (kPa)Mounting KitCode NumberT-3x11V-3000-8012V-3000-80031/2 or 3/4 (DN15 or DN20)5/16 in. (8 mm) Stroke3 to 6 (21 to 41)VG7000-100134 to 8 (28 to 55)VG7000-100239 to 13 (62 to 90)VG7000-10033T-3x11V-3000-8012V-3000-80031 or 1-1/4 (DN25 or DN32)1/2 in. (13 mm) Stroke3 to 6 (21 to 41)VG7000-100434 to 8 (28 to 55)VG7000-100539 to 13 (62 to 90)VG7000-10063T-3x11V-3000-8012V-3000-80031-1/2 or 2 (DN40 or DN50)3/4 in. (19 mm) Stroke3 to 6 (21 to 41)VG7000-100734 to 8 (28 to 55)VG7000-100839 to 13 (62 to 90)VG7000-10093V-3801-80011/2 or 3/4 (DN15 or DN20)5/16 in. (8 mm) Stroke3 to 6 (21 to 41)VG7000-101034 to 8 (28 to 55)VG7000-101139 to 13 (62 to 90)VG7000-10123V-3801-80011/2 or 3/4 (DN15 or DN20)5/16 in. (8 mm) StrokeKit with Three Springs:3 to 6, 4 to 8, and 9 to 13 (Includes hardware to adapt one valve only.)VG7000-10153MP82/MP831/2 or 3/4 (DN15 or DN20) with Stainless Steel TrimNot ApplicableMP8000-67014MP82/MP831 through 2 (DN25 through DN50) with 1/4 in. Stem and Stainless Steel or Brass TrimNot ApplicableMP8000-67024MP84/MP851-1/2 through 2 (DN40 through DN50) with3/8 in. Stem and Stainless Steel TrimNot ApplicableMP8000-670351.Use all mounting kits with valves with standard threaded stem design only.2.DN is the European designation for body size in metric units (mm).3.The mounting kits include: upper spring seat, spring, stem extension, stem locking screw (or set screw), and a bonnetadaptor for the V-3801-8001. Use this only on valves with threaded stems.4.The mounting kits include: stem nut (1), stem extender nuts (2), stem extender (1), and yoke nut (1).5.The mounting kit includes: stem nuts (2) and yoke nut (1).Table 8: Field Mounting Kits for Electric Actuators1Actuator StyleValve Size, in. (DN)Mounting Kit Code NumberVA-42331/2 through 1-1/4 (DN15 through DN32)None RequiredVA-715x1/2 through 2 (DN15 through DN50)None RequiredVA-720x1 through 2 (DN25 through DN50) for valves with brass trimNone RequiredVA-8x2x1/2 and 3/4 in. (DN15 and DN20)VA-8020-100 (Refit only)VA78x01 through 2 (DN25 through DN50) for valves with brass trimNone Required1.Use all mounting kits with valves with standard threaded stem design only.Next >