The performance specifications are nominal and conform to acceptable industry standards. For applications at conditions beyond these specifications, consult the local Johnson Controls office.Johnson Controls shall not be liable for damages resulting from misapplication or misuse of its products. © 2018 Johnson Controlswww.johnsoncontrols.com1Code No. LIT-1901017Issued August 2018DescriptionThe FX80 Supervisory Controller Control Panel Assembly features a pre-wired, pre-assembled, and pretested standard control panel solution with an FX80 base controller. Such a turnkey solution helps building system integrators achieve installation efficiency and adherence to technical safety standards for building system installations in North America and Canada.The control panel assembly is available in a NEMA Type 1 rated 16 x 20 in. steel enclosure. This small footprint enclosure is optimal for wall mounting in space-constrained locations. The enclosure provides space for up to two additional communication modules in addition to the FX Base Controller. See the FX Supervisory Controller Product Bulletin (LIT-12012250) and FX Supervisory Controller Catalog Page (LIT-1901010) for additional information.In addition to the FX80 supervisory controller, the assembly also contains a power supply incorporating a 5 A circuit breaker, a 96 VA 120/24 VAC transformer, and two 120 VAC outlets. A 5-port Ethernet switch is also provided.The control panel allows for direct wire termination to the controller, making installation, commissioning, and servicing quicker and easier.Features•Consistent layout for all standard control panel solutions simplifies installation and commissioning•Prebuilt, pre-wired, and pretested in anISO-9002 manufacturing facility, whichprovides products of consistently highquality•UL 50-rated, Canadian StandardsAssociation (CSA) approved enclosuremeets local and national coderequirements for the United States andCanada (cULus listed)Repair InformationIf the FX80 Supervisory Control panel assembly fails to operate within its specifications, replace the failed component. For a replacement FX80 Supervisory Control panel assembly, contact the nearest Johnson Controls® representative.FX80 Supervisory Controller Control Panel AssemblyFX80 Supervisory Controller Control Panel Selection Chart *Note: You must purchase device licenses and software maintenance licenses separately. You must fully commission and license the FX80 Supervisory Controller in the field.Technical Specifications Code NumberDescriptionPATW00001FH0*Pre-assembled 16 X 20 in. Type 1 enclosure, which includes: Netgear 5-port switch, 96 VA power supply, and the FX-SC8BASE-0 (FX80 Base controller and SD card). PATX00001FHO*Pre-assembled 16 X 20 in. Type 1 enclosure, which includes: Netgear 5-port switch, 96 VA power supply, and the FX-SC8BWIFI-0 (FX80 Base controller and SD card but with WiFi disabled).FX80 Supervisory Controller Control Panel AssemblyAmbient ConditionsOperating: 32 to 122F (0 to 50C), 10 to 90% RH, noncondensingEnclosure RatingNEMA Type 1Enclosure FinishANSI 61 gray polyester powder coating (perforated panel and enclosure)Dimensions16 x 20 x 6-5/8 in. (406 x 508 x 168 mm)Shipping Weight36 lb (16.3 kg)ComplianceUnitedStates:Panel UL 508A rated (cULus Listed), Enclosure UL 50 RatedCanada:CSA ApprovedSeismic Approval:OSHPD Special Seismic Certification Preapproval OSP-0140-10European Single Point of Contact:NA/SA Single Point of Contact:APAC Single Point of Contact:JOHNSON CONTROLSWESTENDHOF 345143 ESSENGERMANYJOHNSON CONTROLS507 E MICHIGAN STMILWAUKEE WI 53202USAJOHNSON CONTROLSC/O CONTROLS PRODUCT MANAGEMENTNO. 22 BLOCK D NEW DISTRICTWUXI JIANGSU PROVINCE 214142CHINAFX80 Supervisory Controller Control Panel Assembly Catalog PageNext >