Cool M37920 FocusPro ® TH5320R Wireless Thermostat Thermostat Sans Fil Termóstato inalámbrico Operating ManualM28430 Read and save these instructions. Need Help? For assistance with this product please visit honeywellhome.com or call Customer Care toll-free at 1-800-468-1502 ® U.S. Registered Trademark. Patents pending ©2019 Resideo Technologies, Inc. All rights reserved. Battery Holder Press down and pull to remove batteries. Batteries should be replaced once a year (see page 11). CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). 1 69-2094EFS—07 Français : voir la page 15 • Español: vea la página 30 Contents About your new thermostat Initial setup .....................................................2 Quick reference to controls....................3 Quick reference to display ......................4 Operation Fan settings (auto/on) .............................5 System settings (heat/cool) ..................6 Auto-changeover (heat/cool) ...............7 Remote control .............................................8 Display outdoor climate ..........................9 Find lost remote control ..........................9 Compressor protection .........................10 Appendices Battery replacement ...............................11 In case of difficulty ..................................13 Limited warranty .......................................14 Regulatory information .........................45Operating Manual 69-2094EFS—07 2 About your new thermostat Your new wireless thermostat is pre-set for immediate use. All you have to do is choose the settings you prefer: 1. Select fan setting (Auto/On) ..............................................................See page 5 2. Select system setting (Heat/Cool) .................................................See page 6FocusPro® TH5320R Wireless Thermostat 3 69-2094EFS—07 Quick reference to controls M28431 Digital display (see page 4) Battery holder (see page 11) Temperature buttons Press to adjust temperature Function buttons Press to select the function displayed just above each button. (Functions change depending on the task.)Operating Manual 69-2094EFS—07 4 Auto Fan Aux Heat On SystemMore Heat Heat Setting M28432 Indoor 75 75 Replace Battery Quick reference to display screen Current inside temperatureLow battery warnings (see pages 11-12) Temperature setting More Press to view outdoor climate (if outdoor sensor is installed), or to find a misplaced remote control if installed (see page 9) Auxillary heat (Only for heat pumps with auxillary heat) System status Heat On/Cool On (If flashing, see page 10) System setting Heat/Cool/Auto/Off/Em Heat (see page 6) Fan Setting Auto/On (see page 5)FocusPro® TH5320R Wireless Thermostat 5 69-2094EFS—07 Select the fan setting Auto FanSystemMore Heat M28433 On FanSystemMore Heat M28434 Press FAN to select Auto or On. In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to “On,” the fan runs continuously. Note: Options may vary depending on your heating/ cooling equipment.Operating Manual 69-2094EFS—07 6 Select the system setting • Heat: Thermostat controls only the heating system. • Cool: Thermostat controls only the cooling system. • Off: All systems are off. • Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature. • Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat. Compressor is locked out. Press SYSTEM to select: Auto FanSystemMore Heat M28435 Auto FanSystemMore Cool M28436 Note: Options may vary depending on your heating/ cooling equipment.FocusPro® TH5320R Wireless Thermostat 7 69-2094EFS—07 Auto Changeover (heat/cool) Auto changeover is a feature used in climates where both air conditioning and heating are often used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3 degree separation. Auto FanSystemMore Auto MCR28437 Note: The Auto system setting may not appear, depending on how your thermostat was installed. Press until screen displays “Auto”Next >