EISW8-100T Plug and Play Switching Hub for Automation Systems Installation Guide The EISW8-100T 8-port switching hub is designed for networked automation applica- tions. Like all Ethernet switches from Contemporary Controls, it features non-block- ing (full wire-speed) operation. It divides an Ethernet network into eight collision domains—“bridging” data links to create larger network diameters than possible with repeating hubs. Each port automatically negotiates its data rate to either 10 Mbps or 100 Mbps—controlling data flow with the PAUSE function in full-duplex links or with the backpressure method in half-duplex links. The switch provides preamble regeneration with symmetry and amplitude compensation, retiming signals to eliminate jitter. Digital pre-emphasis compensates for inherent signal strength roll-off. Link integrity is monitored, verifying that a working adapter or hub is on the distant end of a segment. Port assignments are learned by reading Ethernet frames and logging the source addresses to a table. Throughput is improved by restricting traffic to those ports party to a data exchange while other data is simultaneously exchanged on other ports. Store-and-forward operation is implemented, and broadcast, multicast, or unicast transmissions are received by all ports. The EISW8-100T has eight Auto-MDIX ports for attaching local devices. Each port has one LED that glows with an established link and flashes with activity. The unit features dual power inputs with wide-ranging voltages (12-48V DC or 24V AC). For power redundancy, two DC supplies can be used. A normally open (NO) fault relay contact held closed, opens upon a P1 or P2 power failure. This contact is rated up to 24V DC at 1A. A wide operating temperature range of –40°C to +75°C make the EISW8 suitable for outdoor applications.Specifications Electrical INPUT DC AC Voltage: 12-48 V 24 V Power: 2.5 W 4 VA Frequency: N/A 47–63 Hz Class 2 Circuits Only Environmental Operating Temperature: –40°C to +75°C Storage Temperature: –40°C to +85°C Humidity, non-cond.: 5% to 95% Protection: IP 30 Mounting TS-35 DIN-rail/ wall-mounted Product Weight 300g Regulatory Compliance CE Mark; CFR 47 Part 15, Class A; UL; UKCA Functional Compliance: IEEE 802.3/3u/3x/1p/3az Data Rates: 10 and 100 Mbps Signalling: 10BASE-T and 100BASE-TX Connectors: Shielded RJ-45 Segment length: 100 m (maximum) LED Indicators P1 green (PWR1) P2 green (PWR2) Per Ethernet Port: Link/Activity green/flashing RJ-45 Connector Pin Assignments Pin Function 1 TD+ 2 TD– 3 RD+ 6 RD– (All other pins are unused.) Mechanical Dimensions: 41 x 70 x 115 mm (W x D x H) 70.00 18.00 3.50 103.00 5.50 Side View Top View Rear View DC Input: 12-48V — , 0.2A max. AC Input 24V~, 0.16A max. V1+ 1 2 3 4 5 6 V1- PWR1 Max. Fault Alarm Loading: 24V, 1A V2+V2- PWR2Fault 115.00 41.00 Front View P1P2 ACTLNK 10/100 1 2 3 4 5 6 7 8 ---Power Sourcing Options Power Considerations The EISW can be powered from either a single source of AC or DC. Dual source power- ing is possible with two DC supplies isolated from one another. Recommended size for solid power conductors is 16–22 AWG; for stranded conductors, use 16–18 AWG. Input connections are reverse polarity protected. The earthing screw terminal on the switch must be grounded if there is no other option for grounding the case. Network Connections The switch employs Auto-MDIX technology so that either straight-through or crossover cables can be used to connect to network interface adapters or to another hub. LED Indicators The “P1” LED glows green to indicate Power Input 1 (PWR1) has power, and the “P2” LED glows green to indicate Power Input 2 (PWR2) has power. Each Ethernet port has a LNK/ACT LED that glows solid green to indicate an established 10 or 100 Mbps link, and flashes green to indicate that network traffic is occurring over that port. Single Source Powering PWR1 with AC PWR1 with DC 12-48 VDC + 12-48 VDC + 12-48 VDC + * V1+ 1 2 3 4 5 6 V1- PWR1 V2+V2- PWR2Fault V1+ 1 2 3 4 5 6 V1- PWR1 V2+V2- PWR2Fault V1+ 1 2 3 4 5 6 V1- PWR1 V2+V2- PWR2Fault 24 VAC Primary * Possible grounded secondary. Redundant Powering PWR1 with DC PWR2 with DC Power supplies must be isolated from each other.Need more help installing this product? For more information, visit www.ccontrols.com. If contacting our office, ask for Technical Support. Warranty Contemporary Controls (CC) warrants this product to the original purchaser for five years from the shipping date. If it fails to operate in compliance with its specification during this period, CC will, at its option, repair or replace the product at no charge. The customer is responsible for shipping the product; CC assumes no responsibility for the product until received. This limited warranty covers products only as delivered. If user modification damages the product, repair or replacement are not covered. Damage from abuse, accident, disaster, misuse, or incorrect installation are not covered. This warranty in no way warrants suitability of the product for any specific application. More warranty information can be found at www.ccontrols.com. Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Returning Products for Repair Return the product to the location where it was purchased by following the instructions at the URL below: www.ccontrols.com/rma.htm Declaration of Conformity Information about the regulatory compliance of this product can be found at the URL below: www.ccontrols.com/compliance.htm April 2022 TD220100-0IBNext >