DS-EISW8000-AA1 Data Sheet – EISW8-100T EISW8-100T Ethernet Switch Features… • Plug-and-Play operation • 10BASE-T/100BASE-TX • Shielded RJ-45 connectors • Auto-negotiation of speed and duplex • Auto-MDIX supports cable inversion • Diagnostic LEDs • DIN-rail and wall mounting • Rugged metal enclosure • Enhanced EMC compliance • UL listed, CE mark • 24 VAC/VDC powered • 1K MAC address support • Operating Temp range –40°C to +75°C The EISW8-100T switching hub is an eight-port unmanaged Ethernet switch that provides 10/100 Mbps performance on all ports to accommodate a range of control devices and workstations commonly found in an automation project. For 10 Mbps legacy devices, the switch will automatically reduce its port-speed accordingly. This low-cost compact unit utilizes a rugged metal enclosure, with DIN-rail and wall mounting installation. The switch supports plug-and-play operation and requires no configuration. All ports automatically configure their data rate and duplex using the Auto- negotiation protocol. Depending on the capability of the link partner, communication is set at 10 or 100 Mbps and at either half- or full-duplex. Each port accommodates either a straight-through or crossover cable using the Auto-MDIX protocol. The unit is powered from a choice of low-voltages (AC or DC). Redundant power connections are provided for back-up power schemes. LEDs assist in troubleshooting. EISW8-100T Ethernet Switch 10/100 Mbps, Wide-Temp, Compact Size EISW8-100T DS-EISW8000-AA1 Data Sheet – EISW8-100T 2 Overview The EISW8-100T Switch can be used in control panel installations where DIN-rail space is at a premium by requiring a width of only 41 mm of rail space. A metal DIN-rail clip attached to the steel enclosure can survive the toughest installation. In addition, the unit comes equipped with a wall-mount kit for wall-mount installations. The EISW8-100T has eight Auto-MDIX ports for attaching local devices. Each port has one LED that glows with an established link and flashes with activity which assists in troubleshooting connection issues. The unit features dual power inputs with wide-ranging voltages (12-48 VDC or 24 VAC). For power redundancy, two DC supplies can be used. A normally open (NO) fault relay contact held closed, opens upon a P1 or P2 power failure. This contact is rated up to 24 VDC at 1A. A wide operating temperature range of –40°C to +75°C make the EISW8 suitable for outdoor applications. A removable power connector facilitates the servicing of the unit. The switch is UL Listed for Industrial Control Equipment. It complies with CFR 47 Part 15 Class A and carries the CE Mark. It is UKCA compliant. Quick Disconnect 6-pin Connector provides connections to a DC or AC source and a connection for a backup DC source Power LEDs P1: glows green to indicate power input 1 (PWR1) has power. P2: glows green to indicate power input 2 (PWR2) has power Fault Relay for Monitoring Power (pins 3 and 4) Copper Ports Eight 10BASE-T/100BASE-TX RJ45 auto-MDI/MDI-X ports Port LEDs Each port has a LNK/ACT LED The LED glows green to indicate the link is established. It flashes to indicate the switch is transmitting/ receiving data over that port Earthing Screw Terminal 41 mm DIN-rail Clip or Wall-mount Panel for convenient and versatile installation Metal Enclosure rugged packaging for tough environmentsDS-EISW8000-AA1 Data Sheet – EISW8-100T 3 RJ-45 Connector Pin Assignments PinFunction 1TD+ 2TD– 3RD+ 4Not Used 5Not Used 6RD– 7Not Used 8Not Used Mechanical Drawing Dimensions: 41 x 70 x 115 mm (W x D x H) Specifications Power Requirements 12–48 VDC 2.5 W or 24 VAC ±10% 4 VA 47–63 Hz Operating Temperature –40°C to +75°C Storage Temperature –40°C to +85°C Relative Humidity 5–95%, non-condensing Protection IP30 Mounting TS-35 DIN-rail/wall-mounted Shipping Weight 0.66 lb (0.3 kg) Ethernet Communications IEEE 802.3/3u/3x/1p/3az 10/100 Mbps data rate using RJ-45 connectors, 100 m (max) LEDs P1 Green = PWR1 has power P2 Green = PWR2 has power LNK Green = 10/100Mbps link established ACT Flashing Green = Data Regulatory Compliance CE Mark; CFR 47, Part 15 Class A; UL; UKCA 70.00 18.00 3.50 103.00 5.50 Side View Top View Rear View DC Input: 12-48V — , 0.2A max. AC Input 24V~, 0.16A max. V1+ 1 2 3 4 5 6 V1- PWR1 Max. Fault Alarm Loading: 24V, 1A V2+V2- PWR2Fault 115.00 41.00 Front View P1P2 ACTLNK 10/100 1 2 3 4 5 6 7 8 ---DS-EISW8000-AA1 Data Sheet – EISW8-100T April, 2022 www.ccontrols.com Power Considerations The EISW can be powered from either a single source of AC or DC. Dual source powering is possible with two DC supplies isolated from one another. The recommended size for solid power conductors is 16–22 AWG; for stranded conductors, use 16–18 AWG. Input connections are reverse polarity protected. The earthing screw terminal on the switch must be grounded if there is no other option for grounding the case. Typical Switch Installations Model Description EISW8-100T 8-Port 10/100Mbps Wide-Temp Ethernet Switch -40 to +75C Ordering Information EISW8-100T Ethernet Switch EISW8-100T Ethernet Switch EIMK Media Converter EISK5-100T/FC Ethernet Switch Single Source Powering PWR1 with AC PWR1 with DC 12-48 VDC + 12-48 VDC + 12-48 VDC + * V1+ 1 2 3 4 5 6 V1- PWR1 V2+V2- PWR2Fault V1+ 1 2 3 4 5 6 V1- PWR1 V2+V2- PWR2Fault V1+ 1 2 3 4 5 6 V1- PWR1 V2+V2- PWR2Fault 24 VAC Primary * Possible grounded secondary. Redundant Powering PWR1 with DC PWR2 with DC Power supplies must be isolated from each other.Next >