DS-EISK5H00-BA2 EISK5-100T/H SHEET data • DIN-rail mounting • Rugged metal enclosure • Diagnostic LEDs • Enhanced EMC compliance • UL 508 listed, c-UL listed, CE mark • 24 VAC/VDC powered One benefit of switched Ethernet technology is that the switch restricts directed messages to only those ports party to the communication. This improves overall network throughput by not burdening end stations with useless traffic. However, this feature makes protocol debugging difficult because a protocol analyser tool attached to an unused port on the switch cannot observe any directed messages of interest. In the past, the solution was to change out the switching hub with a repeating hub but with the Skorpion Diagnostic Switch this is unnecessary. The Skorpion Diagnostic Switch retains all the virtues of switched Ethernet technology such as 10/100 Mbps data rates on individual segments, auto-negotiation, Auto-MDIX but with one exception — no address learning. All messages — directed, multicast, broadcast — are flooded to all ports on the switch allowing a protocol analyser tool such as Wireshark ® the ability to observe all traffic on the network. The Skorpion Diagnostic Switch can be permanently installed on an installation or replaced with a regular Skorpion switch once a system is commissioned. This device can also be useful when developing embedded Ethernet devices because you can connect the Skorpion Diagnostic Switch between two embedded Ethernet devices and view their messages using Wireshark. 5-Port Skorpion Diagnostic Switch Plug and Play Diagnostic Switch for Protocol Debugging • Plug-and-Play operation • 10BASE-T/100BASE-TX • Shielded RJ-45 connectors • Auto-negotiation of speed and duplex • Auto-MDIX supports cable inversion Wireshark is a registered trademark of the Wireshark Foundation which can be accessed at www.wireshark.org.DS-EISK5H00-BA2Page 2 Data Sheet — EISK5-100T/H Overview Quick Disconnect 4-pin Power Connector provides connections to a DC or AC source and a connection for a backup DC source. Link/Rate/Duplex LEDs All ports have activity and link LEDs. Each “L” LED glows green when the data rate is 100 Mbps or yellow when the rate is 10 Mbps. The LED will flash with data. Each “D” LED glows green if the link is in full-duplex mode and is off if the link is operating in half-duplex mode. 35 mm Din-rail Clip for convenient installation in control panels Writable Label for identifying each link partner The EISK5-100T/H can be used for control panel installations where one needs the ability to diagnose problems in the field. It can also be used in a development environment when debugging code. A metal DIN-rail clip attached to the aluminium enclosure can survive the toughest installation. A writable side label allows the installer an opportunity to document field cabling locations right on the unit. The EISK5-100T/H is powered from a source of either 24 VAC ±10% or 10–36 VDC. With redundant power connections, a backup power scheme can be supported. A removable power connector facilitates the servicing of the unit. LEDs built into the RJ-45 connector indicate data rate and activity on each of the five ports. For each port, the data rate will be indicated along with port activity — thereby greatly assisting in troubleshooting connection issues. The EISK5-100T/H is UL 508 Listed and c-UL Listed for Industrial Control Equipment. It complies with CFR 47 Part 15 Class A, and carries the CE Mark. It is RoHS compliant. Power LED indicates the unit is being powered Copper Ports shielded RJ-45 connectors Metal Enclosure rugged packaging for tough environmentsDS-EISK5H00-BA2Page 3 Data Sheet — EISK5-100T/H Specifications Power Requirements 10–36 VDC 3 W or 24 VAC ±10% 7 VA 47–63 Hz Operating Temperature 0°C to 60°C Storage Temperature –40°C to 85°C Relative Humidity 10–95%, non-condensing Protection IP30 Mounting TS-35 DIN-rail Shipping Weight 1 lb (0.45 kg) Ethernet Communications IEEE 802.3 10/100 Mbps data rate using RJ-45 connectors, 100 m (max) LEDs Power Green = power OK “L” LEDs Green = 100 Mbps communication established Yellow = 10 Mbps communication established Flashing = data transmissions occurring “D” LEDs Green = Full-duplex communication established Off = Half-duplex communication established Regulatory Compliance CE Mark; CFR 47, Part 15 Class A; RoHS; UL 508 Industrial Control Equipment PinFunction 1TD+ 2TD– 3RD+ 4Not Used 5Not Used 6RD– 7Not Used 8Not Used RJ-45 Connector Pin Assignments Mechanical DrawingDS-EISK5H00-BA2 — July 2011Page 4 Data Sheet — EISK5-100T/H Power Considerations Ordering Information ModelDescription EISK5-100T/H5 ports 10/100 Mbps Skorpion diagnostic switch Typical Installations Applied voltage must be 10–36 VDC or 24 VAC ±10% and deliver a current commensurate with power consumption. The recommended size for solid power conductors is 16–20 AWG; and for stranded conductors use 16–18 AWG. Zero volts (COM) is isolated from chassis (earth). Input connections are reverse-polarity protected.Next >