DS-EIMK1000-AB1 Data Sheet – EIMK The EIMK Skorpion Media Converter series makes the conversion of an Ethernet copper segment to ﬁber simple. By operating full- duplex at 100 Mbps provides the highest possible performance on 100 Mbps links. The EIMK is a true media converter and not just a two-port Ethernet switch. Therefore performance is enhanced by not introducing the store-and-forward data latency inherent in a switch. Both multimode and single-mode models are available with SC connectors, ST connectors model is only available in multimode. Fiber distances of up to 15 km are possible with the single-mode model — up to 2 km with the multimode models. On the copper side, both MDI and MDIX ports are available to compliment either an end station port or a switch port. EIMK Industrial Ethernet Media Converters Making the Copper to Fiber Connection • Plug-and-Play operation • 100BASE-TX/100BASE-FX conversion • Shielded RJ-45 and SC/ST-style ﬁber optic connectors • Full-duplex operation • MDI and MDIX copper ports • Far End Fault feature • DIN-rail mounting • Rugged metal enclosure • Diagnostic LEDs • Enhanced EMC compliance • UL 508 listed, c-UL listed, CE mark • 24 VAC/VDC poweredDS-EIMK1000-AB1 Data Sheet – EIMK 2 Overview Each of the three models supports full-duplex operation for 100BASE-TX and 100BASE-FX segments. Two models support multimode ﬁber optic connections: the EIMK-100T/FT makes the ﬁber optic connection via ST-style connectors, whereas the EIMK-100T/FC does so via SC connectors. The model EIMK-100T/FCS supports single-mode ﬁber via SC connectors. Maximum distance with 62.5/125 µm multimode ﬁber cables is 2 km while single-mode ﬁber can span up to 15 km. Two RJ-45 connectors (one MDIX port and one MDI port) allow either straight-through or crossover copper cabling. Link and activity LEDs allow troubleshooting on both the copper and ﬁber sides. Far End Fault feature allows the stations on both ends of the ﬁber to indicate established link (Link LED on) or indicate if there is a half break or no link (Link LED off). Link LEDs also indicate if a copper Ethernet connection is established. If a half-break or no link on the ﬁber side occurs, the copper port will also go down. This provides network fault indication on both ends. There must be a valid link on both copper and ﬁber sides in order for link LEDs to light up solid, indicating a complete connection. Activity (ACT) LEDs indicate data trafﬁc when ﬂashing. All units mount on TS-35 DIN-rail and operate from either a 24 V AC or DC power source while offering redundant power connections. By incorporating a half-wave rectiﬁer design, the sharing of the power source with other half-wave devices is possible. Designed for commercial and industrial Ethernet applications, all models comply with EMC immunity and emissions compatibility standards for industrial environments. RJ-45 Ethernet Connectors Both an MDI connector (to a switch) and MDIX connector (to an end station) are available. Fiber Connectors Multimode models are available with either ST or SC style connectors while the single mode version is available with SC style connectors. Diagnostic LEDs Diagnostic LEDs for both copper and ﬁber sides. Link = green with an established link Activity = green and ﬂashes with dataDS-EIMK1000-AB1 Data Sheet – EIMK 3 Speciﬁcations Power Requirements 10–36 VDC ±10% 3W or 24 VAC ±10% 5VA 47–63 Hz Operating Temperature 0°C to 60°C Storage Temperature –40°C to 85°C Relative Humidity 10–95%, non-condensing Protection IP30 Mounting TS-35 DIN-rail Shipping Weight 1 lb (0.45 kg) Fiber Transceivers TX Power (min) RX (min) Wavelength Optical Budget Multimode –19 dBm –32 dBm 1310 nm 13 dB Single-mode –15 dBm –32 dBm 1310 nm 17 dB Ethernet Communications IEEE 802.3 100 Mbps data rate 100BASE-TX using RJ-45 connectors (MDI and MDIX), 100 m (max) 100BASE-FX multimode using SC or ST connectors, 2 km (max) 100BASE-FX single-mode using SC connectors, 15 km (max) LEDs Power Green = power OK Link Green = communication established Activity Green = data transmissions occurring (ﬂashes) Regulatory Compliance CE Mark; CFR 47, Part 15 Class A; RoHS; UL 508 Industrial Control Equipment PinFunction 1TD+ 2TD– 3RD+ 4N/C 5N/C 6RD– 7N/C 8N/C RJ-45 Connector Pin AssignmentsMechanical DrawingDS-EIMK1000-AB1 Data Sheet – EIMK August, 2017 www.ccontrols.com Power Considerations Ordering Information ModelDescription EIMK-100T/FTSkorpion 100BASE-TX/100BASE-FX MM ST-Fiber Media Converter EIMK-100T/FCSkorpion 100BASE-TX/100BASE-FX MM SC-Fiber Media Converter EIMK-100T/FCSSkorpion 100BASE-TX/100BASE-FX SM SC-Fiber Media Converter Typical Media Converter Installations Applied voltage must be in the speciﬁed range and deliver a current commensurate with power consumption. The recommended size for solid power conductors is 16–20 AWG; and for stranded conductors use 16–18 AWG. Zero volts (COM) is isolated from chassis (earth). Input connections are reverse-polarity protected.Next >