Automation Components, Inc.WIRELESS | WT2630WIRELESS | ## Call: 1-888-967-5224 | Web: www.workaci.com PRODUCT SPECIFICATIONSInput Voltage:Battery Life:Operating Temperature Range:Operating Humidity Range:Storage Temperature Range:Accuracy:Data Protocol:RF Characteristics:Sensor Data Transmission Time:Transmission Distance:Enclosure Material | Flammability Rating:Product Dimensions:Product Weight:Battery; 1 (Duracell DL123A), Lithium 3V 1400 mAh 45 mA maximum 2-3 years typical32 to 104º F (0 to 40ºC) 5 to 65%, Non-condensing40 to 122ºF (4 to 50ºC) | 5 to 65% RH, Non-condensing+/- 1ºF (+/- 0.555ºC) 12 bit resolutionIEEE 802.15.4-2003/2006900 MHz, Operating Frequency 10 channels between 902 – 928 MHzTransmitter Power: 11 dBm | Receiver Sensitivity: -11 dBm 75 seconds (default) | 300 seconds (optional)200 – 300 ft horizontally depending on building type and construction, and typically one oor above and below the transceiver verticallyRoom: ABS Plastic | UL 94 HB | Ruggedized Enclosure: ABS Plastic | UL94-5VARoom: (L) 4.50” (114.30 mm) x (W) 2.75” (69.85 mm) x (H) 1.12” (28.45 mm)Ruggedized Enclosure: (L) 4.25” (107.95 mm) x (W) 2.63” (66.80 mm) x (H) 1.24” (31.50 mm) Room: 0.30 lbs (0.14 kg) | Ruggedized Enclosure: 0.35 lbs (0.16 kg)WT2630Room, Wall Mount TemperatureThe WT2630 series room sensors are battery operated and work on the 900MHz spread spectrum technology which allows for easy installation without long wire runs and expensive labor. Wireless room sensors can be used in museums, churches and historical sites where traditional wired sensor installation would cause damage or be expensive to install. The sensors can be used in new construction or to retrot HVAC, building automation, and light industrial systems with minimal downtime and expense compared to hardwired sensors. The WT2630 is available in three dierent congurations to monitor temperature (WT2630A), temperature, set point and override for local temperature and afterhours control (WT2630B), and temperature with override (WT2630C), to send the data wirelessly to an RM2432D receiver that converts the wireless signal to voltage input to a DDC controller, or to a transceiver that will send the data to a BAS using BACnet, Modbus, or Lonworks protocol. Transmission distance in a typical building is 200-300 feet horizontal depending on the layout and construction of the building, and one oor above and one oor below the transceiver. Sensor distance and reliability can be increased with the addition of a RR2552B(s) repeater.Applications: Museums, Churches, Historical Buildings & New Construction The WT2630 Series is covered by ACI's Two (2) Year Limited Warranty. The warranty can be found in the front of ACI's Sensors & Transmitters catalog, as well as on ACI's website, www.workaci.com.RoomRuggedizedEnclosureAutomation Components, Inc.WIRELESS | WT2630WIRELESS | ## Call: 1-888-967-5224 | Web: www.workaci.com 2.75” (69.85mm)4.50”(114.30mm)1.12”(28.45mm)1.24”(31.50mm)4.25”(107.95mm)2.63” (66.80mm)DIMENSIONAL DRAWINGFront ViewRight ViewTop ViewRoomRuggedized EnclosureSTANDARD ORDERINGModel #WT2630AWT2630A-300WT2630ARWT2630AR-300WT2630BWT2630B-300WT2630CWT2630C-300Item #130659137003134791----130660137004130661----DescriptionWireless Room Temperature Sensor, Standard EnclosureWireless Room Temperature Sensor, Standard Enclosure, 300 Second IntervalWireless Room Temperature Sensor, Ruggedized EnclosureWireless Room Temperature Sensor, Ruggedized Enclosure, 300 Second IntervalWireless Room Temperature Sensor (Setpoint & Override), Standard EnclosureWireless Room Temperature Sensor (Setpoint & Override), Standard Enclosure, 300 Second IntervalWireless Room Temperature Sensor (Override), Standard EnclosureWireless Room Temperature Sensor (Override), Standard Enclosure, 300 Second Interval-OR-Model # Example:137003WT2630A-300Next >