DS-EISK1600-BA1 EISK16-100T SHEET data • DIN-rail mounting • Rugged metal enclosure • Diagnostic LEDs • Enhanced EMC compliance • UL 508 listed, c-UL listed, CE mark • 24 VAC/VDC powered The EISK16-100T Skorpion Switch is a sixteen-port unmanaged Ethernet switch that provides 100 Mbps performance on all ports to accommodate a range of control devices and workstations commonly found in an automation project. For 10 Mbps legacy devices, the switch will automatically reduce its port-speed accordingly. This low-cost compact unit utilizes a rugged metal enclosure and is intended for installation in control panels using DIN-rail mounting. This is a plug-and-play Ethernet switch that requires no configuration. All ports automatically configure their data rate and duplex using the Auto-negotiation protocol. Depending on the capability of the link partner, communication is set at 10 or 100 Mbps and at either half- or full-duplex. Each port accommodates either a straight-through or crossover cable using the Auto-MDIX protocol. The unit is powered from a choice of low-voltages (AC or DC). Redundant power connections are provided for back-up power schemes. LEDs assist in troubleshooting. EISK16-100T Skorpion Switch Cost Effective, 100 Mbps-speed — Compact Size • Plug-and-Play operation • 10BASE-T/100BASE-TX • Shielded RJ-45 connectors • Auto-negotiation of speed and duplex • Auto-MDIX supports cable inversionDS-EISK1600-BA1Page 2 Data Sheet — EISK16-100T Overview Quick Disconnect 4-pin Power Connector provides connections to a DC or AC source and a connection for a backup DC source. Link/Rate/Duplex LEDs All ports have activity and link LEDs. Each “L” LED glows green when the data rate is 100 Mbps or yellow when the rate is 10 Mbps. The LED will flash with data. Each “D” LED is off if the link is to a 10 Mbps legacy device. 35 mm Din-rail Clip for convenient installation in control panels Writeable Label for identifying each link partner The Skorpion Switch is intended for control panel installations where DIN-rail space is at a premium by requiring a width of only 41 mm of rail space. A metal DIN-rail clip attached to the aluminium enclosure can survive the toughest installation. A writable side label allows the installer an opportunity to document field cabling locations right on the unit. The switch can powered from either a 10–36 VDC or 24 VAC (±10%) source. Its half-wave rectified low-voltage power supply allows the sharing of power with other 24 VAC/VDC control devices from a common power supply. With redundant power connections, a backup power scheme can be supported. A removable power connector facilitates the servicing of the unit. LEDs built into the connector indicate data rate and activity on each of the five ports — greatly assisting in troubleshooting connection issues. The switch is UL 508 Listed and c-UL Listed for Industrial Control Equipment. It complies with CFR 47 Part 15 Class A, and carries the CE Mark. It is RoHS compliant. Power LED indicates the unit is being powered Copper Ports shielded RJ-45 connectors Metal Enclosure rugged packaging for tough environmentsDS-EISK1600-BA1Page 3 Data Sheet — EISK16-100T Specifications Power Requirements 10–36 VDC 10 W or 24 VAC ±10% 14 VA 47–63 Hz Operating Temperature 0°C to 60°C Storage Temperature –40°C to 85°C Relative Humidity 10–95%, non-condensing Protection IP30 Mounting TS-35 DIN-rail Shipping Weight 1 lb (0.45 kg) Ethernet Communications IEEE 802.3 10/100 Mbps data rate using RJ-45 connectors, 100 m (max) LEDs Power Green = power OK “L” LEDs Green = 100 Mbps communication established Yellow = 10 Mbps communication established Flashing = data transmissions occurring “D” LEDs Green = Full-duplex communication established Off = Half-duplex communication established Regulatory Compliance CE Mark; CFR 47, Part 15 Class A; RoHS; UL 508 Industrial Control Equipment PinFunction 1TD+ 2TD– 3RD+ 4Not Used 5Not Used 6RD– 7Not Used 8Not Used RJ-45 Connector Pin Assignments Mechanical DrawingDS-EISK1600-BA1 — June 2011Page 4 Data Sheet — EISK16-100T Power Considerations Ordering Information ModelDescription EISK16-100T Skorpion 16-Port 10/100Mbps Switch Typical Switch Installations Applied voltage must be in the specified range and deliver a current commensurate with power consumption. The recommended size for solid power conductors is 16–20 AWG; and for stranded conductors use 16–18 AWG. Zero volts (COM) is isolated from chassis (earth). Input connections are reverse-polarity protected.Next >