Installation and Operation Instructions RM2402D Spread Spectrum Output Receivers AUTOMATION COMPONENTS, INC Version : 5.0 2305 Pleasant View Road I0000692 Middleton, Wisconsin 53562 Page 1 of 4 www.workaci.com (888) 967-5224 6.75"(171.5mm)3.5"(88.9mm)Ø0.190 (4 PLCS.)7.285"(185mm)6.12"(155.5mm) 4.72"(119.89mm)2.367"(60.12mm)TOPTOP VIEWSIDE VIEWAntennaActive LEDData Link LED24VACRJ Connector forDevice Configuration Figure #1 AUTOMATION COMPONENTS, INC Version : 5.0 2305 Pleasant View Road I0000692 Middleton, Wisconsin 53562 Page 2 of 4 www.workaci.com (888) 967-5224 General Description ACI’s mesh network Series 2000 RM2402D receiver utilizes reliable Spread Spectrum Mesh Network Radio technology. Together with other ACI Series 2000 sensors and controls, the system can be used to transmit remote sensor readings, status/alarm indications, and control signals wirelessly. Up to two(2) separate wireless sensor transmitters can be used with one RM2402D. It can be used for remote status/alarm indications and wireless on/off control (wireless relay) applications. The maximum radio transmission distance is dependent on the building type. The maximum open air transmission distance is one mile. In a typical commercial building with steel I-Beam construction, concrete floors with reinforcing rod, and metal stud walls, it can be expected that transmissions will penetrate vertically through floors and horizontally through 200 to 300 feet of walls, furniture and air. Generally a wireless system will cover at least three floors – one floor above, and one floor below the receiver location. In some buildings with favorable transmission characteristics the system may cover more floors. Wireless transceiver or repeaters should be installed within 200 to 300 feet of the RM2402D output module. RR2552 signal repeaters can be installed as needed to increase transmission distance between sensors and receivers. Configuration The RM2402D Receiver can be configured using the RJ connector(as shown in Figure #1) and the configuration software to accept inputs from up to two(2) wireless sensors. Refer to the ACI 2432 Programmer Manual for configuration instruction. Installation Mount the RM2402D Receiver using four #8 screws (mounting dimensions see Figure #1). Using the RM2402D configuration information, connect the digital outputs to the appropriate control input terminals on the controller or contactor using 20AWG wire. Connect 24VAC 60Hz to the input terminals using 18-20AWG wire(See Figure #1). Check all connections before applying power to the unit. PRECAUTIONS SENSORS, REPEATERS AND RECEIVERS SHOULD NOT BE INSTALLED IN THE FOLLOWING AREAS: • INSIDE METAL ENCLOSURE / PANEL • INSIDE OR IMMEDIATELY NEXT TO ELEVATOR SHAFT / ELEVATOR BANKS • IN FRONT OF OR IMMEDIATELY NEXT TO LARGE TREES OR LARGE BODY OF WATER TRANSMISSION DISTANCE AND PERFORMANCE WILL BE DRASTICALLY REDUCED. CAUTION DO NOT USE THIS PRODUCT IN ANY SAFETY RELATED APPLICATIONS WHERE HUMAN LIFE MAY BE AFFECTED. !! AUTOMATION COMPONENTS, INC Version : 5.0 2305 Pleasant View Road I0000692 Middleton, Wisconsin 53562 Page 3 of 4 www.workaci.com (888) 967-5224 PRODUCT SPECIFICATIONS Supply Voltage 24VAC 60Hz, 300mA nominal RF Data Protocol IEEE 802.15.4-2003/2006 Operating Frequency 902-928 MHz Output Power +11 dBm Receiver Sensitivity -110 dBm Open Field Range One mile (line of sight) Data Transmission Interval 75 seconds (standard) Input Digital Output (2 qty) Pilot Duty Relay Contact Closure Contact Rating – 1A @ 24VAC Max Enclosure Material ABS (standard), Polycarbonate (Nema 4X) Rating UL 94 5VA (standard), UL 94 HB (Nema 4X) Environment Operating Temperature 32 to 140°F (0 to 60°C) Operating Humidity 0 to 95% RH (non-condensing) WARRANTY SPECIFICATION The ACI Wireless Series is covered by ACI’s Two (2) Year Limited Warranty, which is located in the front of ACI’S SENSORS & TRANSMITTERS CATALOG or can be found on ACI’s web site: www.workaci.com. WEEE Directive At the end of their useful life the packaging and product should be disposed of via a suitable recycle center. Do not dispose of with household waste. Do not burn. AUTOMATION COMPONENTS, INC Version : 5.0 2305 Pleasant View Road I0000692 Middleton, Wisconsin 53562 Page 4 of 4 www.workaci.com (888) 967-5224 RM2402DE 6.73"(171mm)4.76"(121mm)6.26"(159mm)3.58"(91mm)2.17"(55.1mm)TOP VIEWSIDE VIEW6.73"(171mm)TOPØ0.18"Mounting Holes24VAC Next >