Automation Components, Inc.GAS | QTS-6000 SERIESGAS | ## Call: 1-888-967-5224 | Web: www.workaci.com QTS-6000 SERIESToxic Gas TransmitterThe QTS-6000 Series features a 2-Wire, 4 to 20 mA loop powered output signal and is available in both Commercial and Industrial style enclosures without a display. This series incorporates an Electrochemical sensor which has a typical two to three year life expectancy. All of the sensors can be easily replaced in the eld since the sensors are plugged into an on-board socket or with an integrated sensor assembly for use in the Industrial enclosures. The QTS-6000 is factory congured and can be eld calibrated using the Zero and Span adjustment potentiometers. The commercial grade unit is oered in either a general purpose wall or a duct mount version that includes a ow through pitot tube sampling kit with 18” (0.46 m) of tubing. The tubing length on the duct mount versions should be kept to less than a maximum of 5’ (1.53m) in length in order to not aect the response time. The Industrial grade units include an Aluminum or 316 Stainless Steel enclosure that should be selected based upon the type of gas and environment being monitored. General calibration and bump testing should be completed every 3 months in Hazardous or Explosive type atmospheres while the Commercial grade products should be tested every 6 months. Calibration gases and 0.5 liter/minute gas regulators are not available through ACI. These should be purchased through your local gas supply company or companies such as Portagas® (Praxair®, Inc.) or Mesa Specialty Gases®. Refer to all applicable Federal, State, Provincial and Local Health and Safety laws and regulations before using these products.Applications: Mechanical Rooms, Warehouses, Refrigeration Plants, Industrial Plants, Process Monitoring, Leak Detection, Parking Garages, Auto/Truck Maintenance FacilitiesThe QTS-6000 Series Gas Transmitters are covered by ACI's Two (2) Year Limited Warranty. The warranty can be found in the front of ACI's Sensors & Transmitters catalog, as well as on ACI's website, www.workaci.com.PRODUCT SPECIFICATIONSSupply Voltage | Protection:Supply Current | Power Consumption:Maximum Load @ 24 VDC:Output Signal:Factory Set Range: Accuracy | Repeatability:Response Time (T90):RFI/EMI Protection: Sensor Type:Sensor Life Expectancy:Unit Shelf Life:Replacement Sensor: Recommended Maintenance: Enclosure Specications (Type, Material Type, Flammability, NEMA/IP Rating, Explosion Proof):Intrinsic Safety Barrier Requirement :Operating Temperature:Operating Humidity:Operating Atmospheric Pressure :Recommended Storage Temperature/Humidity:Wiring Connections | Wire Size:Terminal Block Torque Rating:Coverage Area | Mounting Height:Approvals:Product Weight:Product Dimensions (L x W x H):+24 VDC nominal (+12 to 36 VDC Load Dependent) | 0.5A Socketed Pico Fuse25 mA maximum | 0.9 Watts maximum600 Ohms 4-20 mA (2-Wire, Loop Powered)See Gas Sensor Selection & Specication Table on back of data sheet +/- 2.5% of Reading | +/- 1% of Reading< 60 Seconds, typical4.0 Watts @ 1m (3.28 ft) RadiatedElectrochemical, non-consuming2 to 3 years, typical 6 Months from date of purchase (Must be installed and operational) Contact ACIAccuracy & Bump test every 3 to 6 months or as required by Code | Replace sensor as neededCommercial “C”: General Purpose (Wall Mount); ABS Plastic, UL94 V-0; NEMA 1 (IP10)Commercial “D”: General Purpose (Duct Mount); ABS Plastic, UL94 V-0; NEMA 1 (IP10)Commercial “N”: Weatherproof (Wall Mount); ABS Plastic; UL94 V-0; NEMA 4X (IP56)Industrial “E ”: Industrial Connection Head; Aluminum (Epoxy Coated); NEMA 4X (IP56) and Enclosure meets Type 7 & 9 Explosion Proof Class 1 Div. 1, Groups B, C, D also Group A; CSA, FM (Factory Mutual), EX (Explosion Proof), UL listedIndustrial “S ”: Industrial Connection Head; 316 Stainless Steel; NEMA 4X (IP56) and Enclosure meets Type 7 & 9 Explosion Proof Class 1 Div. 1, Groups B, C, D also Group A; CSA, FM (Factory Mutual), EX (Explosion Proof), UL listed28.5 VDC maximum and 300 minimum load See Gas Sensor Selection & Specication Table on back of data sheet 0 to 90% RH, non-condensing (Continuous); 0 to 95% RH, non-condensing (Intermittent)14.696 psi (1.0132 bar) +/- 10%32 to 68ºF (0 to 20ºC) | 15 to 90% RH, Non-Condensing Screw Terminal Blocks, 16 to 24 AWG (0.51 to 1.30 mm) Shielded Twisted Pair0.37 ft-lb (0.502 Nm) NominalSee Gas Sensor Selection & Specication Table on back of data sheetRoHS, CSA-4828-02 (CSA File #: 088890 0 000 for Industrial Enclosure Options Only)Industrial “E”/“S” Enclosures: 5.00 lbs (2.27kg)Commercial “C”/“D”/“N” Enclosures: 2.00 lbs (0.91kg) Commercial “C” Enclosure: 6.60” (167.64 mm) x 4.23” (107.44 mm) x 2.60” (66.04 mm)Commercial “D”& “N” Enclosure: 6.60” (167.64 mm) x 4.23” (107.44 mm) x 3.70” (93.98 mm)Industrial “E”& “S” Enclosure: 10.70” (271.78 mm) x 5.71” (145.04 mm) x 4.25” (107.95 mm)Note: The Cl2, ClO2, HCl, SO2, NO2, NH3, and O3 sensor assemblies are NOT explosion-proof rated | Note: Requirements to meet when installed with CSA Approved Intrinsic Safety Barriers in Class A, B, C & D Certied environments | Note: When installed @ > 3000’ above sea level, the gas transmitters must be veried for accuracy & re-calibrated as needed after installationIndustrialNEMA 4XCommercialNEMA 4XAutomation Components, Inc.GAS | QTS-6000 SERIESDIMENSIONAL DRAWINGTop & Front ViewTop & Front ViewCommercialNEMA 4XGAS | ## Call: 1-888-967-5224 | Web: www.workaci.com Note**: Low = 0.5 to 1.5’ (0.15 to 0.46m) above oor | Mid = 4.0 to 6.0’ (1.20 to 1.83m) above oor | High = 0.5 to 1.5’ (0.15 to 0.46m) below ceilingSENSOR SELECTION AND SPECIFICATIONSymbolN/AH2SHCNCl2ClO2HClSO2NO2CONOH2NH3C2H4OO3Gas Type000110115120123125140150160190211220230240MeasurementN/A0 to 25 ppm0 to 20 ppm0 to 3 ppm0 to 1 ppm0 to 10 ppm0 to 6 ppm0 to 6 ppm0 to 250 ppm0 to 100 ppm0 to 2000 ppm0 to 50 ppm0 to 20 ppm0 to 3 ppmSquare FootageN/A5000 ft (464.5 m)5000 ft (464.5 m)5000 ft (464.5 m)5000 ft (464.5 m)5000 ft (464.5 m)5000 ft (464.5 m)7500 ft (696.7 m)7500 ft (696.7 m)7500 ft (696.7 m)7500 ft (696.7 m)7500 ft (696.7 m)5000 ft (464.5 m)5000 ft (464.5 m)RadiusN/A40 ft (12.2 m)40 ft (12.2 m)40 ft (12.2 m)40 ft (12.2 m)40 ft (12.2 m)40 ft (12.2 m)49 ft (14.9 m)49 ft (14.9 m)49 ft (14.9 m)49 ft (14.9 m)49 ft (14.9 m)40 ft (12.2 m)40 ft (12.2 m)Operating TempN/A-40 to 122ºF (-40 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)-13 to 86ºF (-25 to 30ºC)-4 to 122ºF (-20 to 50ºC)-4 to 122ºF (-20 to 50ºC)Mounting HeightN/ALow**Mid**Low**Low**Mid**Low**Low**Mid**Mid**High**High**Low**MID**Gas TypeTransmitter OnlyHydrogen SulphideHydrogen CyanideChlorineChlorine DioxideHydrogen ChlorideSulphur DioxideNitrogen DioxideCarbon MonoxideNitric OxideHydrogenAmmoniaEthylene OxideOzone000 = Transmitter Only 125 = Hydrogen Chloride 211 = Hydrogen110 = Hydrogen Sulphide 140 = Sulphur Dioxide 220 = Ammonia115 = Hydrogen Cyanide 150 = Nitrogen Dioxide 230 = Ethylene Oxide120 = Chlorine 160 = Carbon Monoxide 240 = Ozone123 = Chlorine Dioxide 190 = Nitric Oxide QTS A. Sensor Series No Selection RequiredC. Conguration Select One (1)C = Commercial NEMA 1 E = Industrial NEMA 4X, 7, 9 (Aluminum)N = Commercial NEMA 4X, Splash Guard S = Industrial NEMA 4X, 7, 9 (316 S.S.)D = Commercial NEMA 1 (Duct Mount; Pitot Tube) E. Enclosure Select One (1)X = Factory ProvidedD. Revision No Selection RequiredQTS61X000061 = Non Indicating 4-20 mA Analog OutputB. Gas Transmitter No Selection Required0 = DefaultF. Factory Supplied No Selection Required0 = DefaultG. Factory Supplied No Selection Required0 = DefaultH. Factory Supplied No Selection Required0 = No Splash Guard | G = Splash Guard (Industrial Enclosures, options E & S above only)I. Splash Guard Select One (1)0 = DefaultJ. Factory Supplied No Selection Required0 = No Special Calibration | X = Non-Standard Calibration | S = Special (Consult Factory)K. Special Features Select One (1)CUSTOM ORDERINGMODEL #Model # Example:0F.SE.XD.120C.61B.QTSA.0G.0GH.I.J.0K.0ACCESSORIES ORDERINGModel #6395-0003Item #126254DescriptionGas Calibration Adaptor-OR-Model # Example:6395-0003126254Ø.50” (12.70 mm)2.60” (66.04 mm)6.60” (167.64 mm)4.20” (106.68 mm)5.07”(128.78mm)Optional Splash Guard Adds 3.10” (78.74mm)5.71”(145.04mm)4.96”(125.98mm)4.50”(114.30mm)Ø4.25”(107.95mm)Ø.28”(7.08mm)7.42” (188.34mm)Ø1.62”(41.15mm)1.35”(34.29mm)IndustrialNEMA 4XNext >